Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Compex WPJ558 HW
Summary of Contents for Compex WPJ558 HW
- Page 1 WPJ558 HW Manual...
- Page 2 Please direct any comments or suggestions about this document to: feedback@compex.com.sg Trademark Information Compex® is a registered trademark of Compex Systems Pte Ltd. Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp. All other brand and product names are trademarks or registered trademarks of their respective owners.
-
Page 3: Table Of Contents
Contents Copyright ......................................2 REVISION HISTORY............................2 REASONS USING DEVELOPMENT KIT ........................... BLOCK DIAGRAM............................2 KEY FEATURES............................... 3 GENERAL INFORMATION..........................3 INFORMATION OF POWER..........................3 CONFIGURATION AND INSTALLATION.....................4 GPIO Bit Mapping..............................4 Interface Connectors.............................4 Serial Port Header..............................5 Serial Console Settings............................5 Precaution when using Serial Converter......................5 Serial Converter Pin Layouts..........................5 JTAG Port Header..............................6 Ethernet Connectors..............................7... -
Page 4: Copyright
Output messages. WPJ558 JTAG Programmer can be used to load in your loader. Ordering Options - Standard Configurations sales@compex.com.sg Currently item codes are not available, please contact our sales team at Configurations are subjected to change without notice BLOCK DIAGRAM... -
Page 5: Key Features
24V ~ 56V DC Supply Support power ：3.3V and 5V MINIPCIE SLOTS supports all Compex WLE series Depend on Order Configuration. JTAG Programmer available to reprogram the flash in case of loader corruption. Serial Converter available to change the TTL signals on board to RS232 signals for debugging. -
Page 6: Configuration And Installation
CONFIGURATION AND INSTALLATION GPIO Bit Mapping GPIO Bit Description Description GPIO Bit EJTAG_TCK Reserved EJTAG_TDI Reserved EJTAG_TDO RSS4 /DIAG LED EJTAG_TMS RSS3 LED BUZZER Reserved SPI_CS_L SWRST SPI_CLK Reserved SPI_MO_SI Reserved SPI_MI_SO Reserved UART_SIN Reserved UART_SOUT RSS2 LED S17_INTn RSS1 LED Interface Connectors The board interface connector pin assignments and signal descriptions are included in the following sections. -
Page 7: Serial Port Header
Serial Port Header The Serial Port (J23) Header signaling is shown in the following table. Signal VCC – 3.3V UART 0 Transmit Data UART 0 Receive Data Note: Our Serial port Implementation requires an external high-impedance serial port not usually available with the serial ports of the notebooks/computers. -
Page 8: Jtag Port Header
Signal Signal Pin Assignment (Serial Connected to Pin on Converters) WPJ344 (Serial Converters) (WPJ344) Pin 1 VCC(3.3V) – Red Pin 1 VCC (3.3V) – Red Pin 2 TX – Green Pin 5 RX – Green Pin 4 RX - Blue Pin 3 TX - Blue Pin 6... -
Page 9: Ethernet Connectors
TX+/POE+ RX-/POE- JTAG PROCESS Minimum Requirement 1. OCD Commander ver2.5.4 2. upbios.tst file (same for all Compex device) 3. uboot.bin file 4. JTAG cable Steps 1. Install the OCD Commander to your PC 2. Plug the JTAG cable to the JTAG port of the device 3. -
Page 10: Build And Install Process
1．OpenWRT will only be supported on WPJ558 with 8MB NOR flash and above. 2．Please ensure that the Ethernet connection is able to ping address = 192.168.1.1 Compiling OpenWRT on WPJ558 + ath9k with patches from Compex. Recommended Linux host: CentOS 6.x, Debian 6.x During the first build of openwrt, about 300MB of various source files will be downloaded from the internet.The downloaded files will be put in openwrt/dl. - Page 11 $ cd $ cd sdkowrt-130603/openwrt $ make Compiling OpenWRT on WPJ558 + ath10k for 11ac radios, with patches from Compex. Recommended Linux host: CentOS 6.x, Debian 6.x During the first build of openwrt, about 300MB of various source files will be downloaded from the internet.The downloaded files will be put in openwrt/dl.
-
Page 12: Board Features
IP Address: 192.168.1.1 Please refer to for more information. http://madwifi.org/ Use of Compex Patches 1. MAC Address from loader 2. Can detect that it is a Compex board Appendix I Board Features TOP SIDE OF BOARD Feature Descriptions Reset button... - Page 13 DC Jack 24V ~ 56V DC Supply LAN port 10/100/1000 Base T Ethernet port WAN/LAN port 10/100/1000 Base T Ethernet port JTAG port JTAG jumper header for programming ① After connecting this two pin with Jumper, the board can provide on-board 5V to the radio card. ②...
Need help?
Do you have a question about the WPJ558 HW and is the answer not in the manual?
Questions and answers