Related Manuals for Oden Control P30R1
Summary of Contents for Oden Control P30R1
- Page 1 ® ODEN ELECTRIC ACTUATORS P30R1 P30R2 P30H P30L1 P30L2 ´ S GUIDE INSTALLATION AND MAINTENANCE MANUAL Version GR 2003-10-26...
-
Page 2: Table Of Contents
DOWNLOAD FROM: WWW.ODENCONTROL.SE ONTENTS 1.0 General information ® 1.1 The Oden family 1.2 Operation and safety instructions 2.0 Technical description 2.1 P30 Basic Unit 2.2.1 Turning module 30R1 2.2.2 Turning module 30R2 2.3.1 Linear module 30L1 2.3.2 Linear module 30L2 2.4 High torque module 30H 2.51 Cable A 2.52 Cable B... -
Page 3: General Information
• 50L with 12 kN max control force This manual deals with: • 220L with 50 kN max control force P30R1, P30R2, P30H ,P30L1 and • 500L with 100 kN max control force P30L2 models The rotary actuators are 90... -
Page 4: P30 Basic Unit
The control signal is normally the standard 4-20 Temperature sensors protect the motor and the P30R1 30R1 A = 10 m A, B or C Max. - Page 5 OPYRIGHT ONTROL AB PUBL collar, as a handle for controlling the valve manu- ally. Version GR 2003-10-26...
-
Page 6: Turning Module 30R2
2.62 Connection board B valve spindles, i.e. when the valve spindle is turned it is making an linear movement. The connection board B is used for digital control. (Contact Oden Control for separate instructions). This module consists of : Version GR 2003-10-26... -
Page 7: Connection Board C
30R1 2.63 Connection board C b. 30R2 The connection board C is used for on/off control. c. 30H + 30R2 (Contact Oden Control for separate instructions). d. 30L1 e. 30L2 2.7 High temperature version — W • Cable with connector ®... -
Page 8: Electric Connections
Put the flange ting flanges. Many valve manufacturers still have adapter to the valve flange. their own internal standards, and Oden Control has designed adapters to the most common Put the linear module 30L1 with its rods to the valves on the market. -
Page 9: The Calibration System Pc/Pc
OPYRIGHT ONTROL AB PUBL PAGE This automatic function as well as the 20-minutes calibration routine can be disabled in the software 5. T HE CALIBRATION SYSTEM - PC/PC 5.1.2 Manual Power Calibration If you for some reason want to make a new cali- The electronic calibration system will automati- bration within 8 hours after a power break, cally find the closed valve position. -
Page 10: Summing Up Of The Pc / Pc - Calibration System
OWNLOAD FROM ODENCONTROL as the calibration position and starts open- 6.0 Maintenance ing the valve. When the valve has reached the requested Control and preventive maintenance should be max. opened angle position, quickly remove carried out only in every three years. In case of the terminal short-circuit. -
Page 11: Trouble Shooting
OPYRIGHT ONTROL AB PUBL These controls can be written down in the notepad when saving the OVP data file. Connect the computer to RS232 and check that the right parameters have been cho- sen in the OVP Software . 7. T ROUBLE SHOOTING Carry out a new Power Calibration (refer to 7.1 Mechanical troubles... - Page 12 ODENCONTROL OWNLOAD FROM Oden P30R2 Version GR 2003-10-26...
- Page 13 OWNLOAD FROM ODENCONTROL Copyright Oden Control AB (publ.) Patent protected in all major countries. US patent 5,913,744 Oden Control AB (publ.) Phone: (+46) 08 767 76 57 Nilstorpsvägen 53 Fax: (+46) 08 767 47 18 E-mail: sales@odencontrol.se 181 47 LIDINGÖ...