Table of Contents
Advertisement
Quick Links
Switch Features
Catalyst 4003 Switch Features
78-6120-10
Product Overview
This chapter provides an overview of the features and components of the
Catalyst 4000 series switches and contains these sections:
Switch Features, page 1-1
•
Switch Components, page 1-12
•
The following sections describe the features of the Catalyst 4000 series switches:
Catalyst 4003 Switch Features, page 1-1
•
Catalyst 4006 Switch Features, page 1-7
•
The Catalyst 4003 switch (see
high-performance, high-density wiring closet applications.
C H A P T E R
Figure
1-1) is a three-slot switch designed for
Catalyst 4000 Series Switch Installation Guide
1
1-1
Advertisement
Table of Contents
Related Manuals for Cisco Catalyst 4124
Summary of Contents for Cisco Catalyst 4124
-
Page 1: Product Overview
Catalyst 4006 Switch Features, page 1-7 • Catalyst 4003 Switch Features The Catalyst 4003 switch (see high-performance, high-density wiring closet applications. 78-6120-10 C H A P T E R Figure 1-1) is a three-slot switch designed for Catalyst 4000 Series Switch Installation Guide... - Page 2 Switching modules (slots 2 and 3) The Catalyst 4003 switch has a Gigabit Ethernet port and a 12-Gbps nonblocking, full-duplex switching fabric that provides connections between the supervisor engine and the switching modules. The Catalyst 4003 switch supports the Supervisor Engine I. The Supervisor Engine I has a 10BASE-T Ethernet management port (RJ-45 connector) and a console port (DCE DB-25 connector).
- Page 3 Chapter 1 Product Overview Table 1-1 Features of the Catalyst 4003 Switch Feature Description Ethernet speeds • • Note Standard equipment • • • Standard management • and support • • • Software management • • • • 78-6120-10 Ethernet (10BASE-T) interface to workstations and repeaters...
- Page 4 Catalyst 4000 Series Switch Installation Guide Full SNMP implementation, including entity-MIB, all relevant standard MIBs, and all relevant Cisco MIBs The first four RMON groups (Ethernet statistics, Alarms, Events, and History supported) on a per-port basis without an optional RMON...
- Page 5 48-port 100BASE-LX10 Fast Ethernet switching module (WS-X4148-FE-LX-MT ) 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ21) 48-port Cisco prestandard Power over Ethernet (PoE) 10/100BASE-TX switching module (WS-X4148-RJ45V) 24-port IEEE 802.3af-compliant PoE 10/100BASE-TX switching module (WS-X4224-RJ45V) 48-port IEEE 802.3af-compliant PoE 10/100BASE-TX RJ-21 switching module (WS-X4248-RJ21V) 48-port IEEE 802.3af-compliant PoE 10/100BASE-TX switching...
- Page 6 3. CLI = command-line interface 4. RMON = Remote Monitoring 5. CDP = Cisco Discovery Protocol 6. CGMP = Cisco Group Management Protocol 7. This module only supports data on the Catalyst 4003. Catalyst 4000 Series Switch Installation Guide 2-port Gigabit Ethernet switching module (WS-X4302-GB)
- Page 7 Fan assembly Switching modules (slots 2 through 6) The Catalyst 4006 switch has two Gigabit Ethernet ports and a 32-Gbps, nonblocking, full-duplex switching fabric that provides connections between the supervisor engine and the switching modules. The Gigabit Ethernet ports can be configured with any combination of shortwave SX, LX/LH, and ZX GBICs.
- Page 8 Standard Layer 2 features: • Catalyst 4000 Series Switch Installation Guide describes the features of the Catalyst 4006 switch. Autonegotiation of link speed on each 10/100 port allows migration to 100BASE-T from a 10BASE-T installed base. and SNMP interfaces consistent with Catalyst 6500 series switches with RMON 1 802.1D Spanning Tree Protocol...
- Page 9 Description Embedded Full SNMP implementation, including entity-MIB, all relevant standard • management MIBs, and all relevant Cisco MIBs The first four RMON groups (Ethernet statistics, Alarms, Events, and • History) on a per-port basis without an optional RMON processing module SPAN, allowing you to redirect traffic from any port or VLAN to a SPAN •...
- Page 10 (WS-X4148-FE-BD-LC) 48-port 100BASE-LX10 Fast Ethernet switching module • (WS-X4148-FE-LX-MT ) 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ21) • 48-port Cisco pre-standard Power over Ethernet (PoE) 10/100BASE-TX • switching module (WS-X4148-RJ45V) 24-port IEEE 802.3af-compliant PoE 10/100BASE-TX switching module • (WS-X4224-RJ45V) 48-port IEEE 802.3af-compliant PoE 10/100BASE-TX RJ-21 switching •...
- Page 11 1. VTP = VLAN Trunking Protocol 2. PAgP = Port Aggregation Protocol 3. CLI = command-line interface 4. RMON = Remote Monitoring 5. CDP = Cisco Discovery Protocol 6. CGMP = Cisco Group Management Protocol 78-6120-10 Catalyst 4000 Series Switch Installation Guide Switch Features 1-11...
-
Page 12: Switch Components
The Catalyst 4003 switch fan assembly has two fans, and the Catalyst 4006 switch has four fans. The fans exhaust air from one side and draw in fresh air on the other side. Catalyst 4003 switch airflow is shown in Figure 1-3. - Page 13 You must install module filler plates on unused switching module slots to ensure Caution proper airflow. Figure 1-3 Fan assembly 78-6120-10 Catalyst 4003 Airflow CAUTION THIS ASSEMBLY CONTAINS ELECTROSTATI C- SENSITIVE DEVICES 100% Catalyst 4000 Series Switch Installation Guide Switch Components 1-13...
- Page 14 Threshold and status level descriptions are provided in the Supplies” To replace a fan assembly, see For complete power specifications, see Note Catalyst 4000 Series Switch Installation Guide 1-14 Po w er Su pp ly Po w er Su pp ly section.
-
Page 15: Power Supplies
The power supply does not have a power switch. Power is provided when the power cord and wiring are installed and plugged into an electrical outlet and the unit is fully seated in the system chassis. - Page 16 DC power connection Catalyst 4000 series switches support redundant power supplies. Each power supply has an individual power cord and status LEDs. The Catalyst 4003 switch has one standard power supply and an optional redundant power supply. The Catalyst 4000 Series Switch Installation Guide...
-
Page 17: Power Supply Leds
When you install and turn on a third power supply on a Catalyst 4006 switch, it provides approximately one-third of the power required by the system. If one power supply fails, the other two immediately generate full power to maintain uninterrupted system operation. -
Page 18: Environmental Monitoring Feature
The supervisor engine monitors the status of each power supply and provides a status report through the switch software. For more information on how the supervisor engine monitors the power supplies, refer to the Catalyst 4500 Series Module Installation Guide.