Subscribe to Our Youtube Channel
Related Manuals for MRC EL-680
Summary of Contents for MRC EL-680
- Page 1 Operation Manual Hand Motion Shaker EL-680 P LEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION 3 , Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529 m rc@mrclab.com MRC.7.15...
-
Page 2: General Information
This manual should always be attached to the equipment and made available to all users. If you have any doubts or inquiries, please contact your supplier or MRC technical service. Do not use the apparatus with liquids which can give off vapors capable of making explosive mixtures. -
Page 3: Equipment Description
E QUIPMENT DESCRIPTION 0 B U Hand Motion Shaker: Electronic regulation between 100 and 960 oscillations per minute. Oscillation amplitude is 9mm. Easily, detachable arms equipped with 8 clamps for attaching and processing up to 8 samples at one time. T ECHNICAL FEATURES 1 B U Voltage supply 115V/230V, 50/60 Hz... - Page 5 1) Power Switch 2) Liquid Crystal Display (LCD) 3) Directional Pad (D-Pad) 4) Enter Button 5) Cursor O peration: Press the Power Switch down into the ON position. The LCD should be lit up showing the main menu. There are three different run modes to choose from.
- Page 6 Run Mode: When selected the shaker will begin at its lowest speed. The speed shown in parenthesis (xxxx) is the set speed controlled by the user. The speed listed to the right is the tachometer read out or the actual speed of the shaker in real time. The speed can be increased/decreased by pressing and holding the up/down arrows on the D-PAD.
- Page 7 Timed Run Mode: The timed run mode features a countdown timer that automatically shuts the shaker off when the time runs out. When selected the user will be taken to the Timed Run Setup Menu and will need to input the run time in hours, minutes, seconds and select the speed for the run.
- Page 8 After selecting START the shaker will begin at the selected speed and the timer will begin counting down. The speed can be adjusted in real time using the up/down arrows on the D-PAD. The speed shown in parenthesis is the target speed controlled by the user and the speed listed to the right is the actual speed as read by the tachometer.
- Page 9 Speed Run Mode: The speed run allows the user to program in a set run speed. Once engaged the timer will begin counting all the way up to 999 hours before the timer overflows back to zero. Select the speed run mode from the main menu and press the Enter Button.
-
Page 10: Maintenance
Note: All run menus will have two speeds listed. The leftmost speed will be displayed inside parenthesis. This is the target speed controlled by the user. The shaker will attempt to match this speed and should do so within ten seconds after making an adjustment. The rightmost speed is the tachometer reading, which shows the user what the shaker is actually running at. -
Page 11: Fuse Replacement
The problem is generally in extreme wear of the bearings or an object obstructing the shaking action. NOTE: If replacement fuse blows almost immediately, repairs may be necessary. If you have any doubts or inquiries concerning operation contact your supplier or MRC technical service. -
Page 12: Display Board
EL-680.00 REPLACEMENT PARTS LIST PartNo DESCRIPTION QTY. 4112 BEARING 1621-2RS 4113 BEARING 1630-2RS 4126 BEARING 1200 NSK 4127 BEARING 6200ZC3 NTN 4259 TIMING BELT 160XL .2"P X 3/8"W NEOPRENE 4507 ALUMINUM MOTOR PULLEY 14 GROOVES 5528 3.75" SUCTION CUP W/ 5/16-18 THREADED POST... - Page 13 ELP680.Q.200 GEAR ELP680.Q.214 DRIVE CLAMP EP6130.650A WIRING HARNESS ASSEMBLY PLP680.203 RIGHT SHAFT EXTENSION PLP680.204 LEFT SHAFT EXTENSION If you have any questions or inquiries concerning installation or ordering of replacement parts please contact your supplier or MRC Technical Service @ 972-3-5595252.
Need help?
Do you have a question about the EL-680 and is the answer not in the manual?
Questions and answers