Related Manuals for Touchboards touchIT
Summary of Contents for Touchboards touchIT
- Page 1 Monitor User Guide Version 0.1 Product specification subject to change without prior notice. Page 1/41...
- Page 2 1. Introduction 2. Connecting the Monitor 3. Using the Monitor 4. Cleaning the screen of LCD Monitor 5. Disclaimer 6. Trouble Shooting 7. Supplement 8. Installation on Wall or Table Top Product specification subject to change without prior notice. Page 2/41...
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS 1. Please read this instructions carefully before using the product and keep it for later reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Clean the product with a damp soft cloth. Do not use liquid or aerosol cleaners as it may cause permanent damage to the screen. -
Page 4: General Function
1 Introduction 1.1 About the Product The monitor consists of a(LED/ TFT) LCD panel and microprocessor -controlled main board. It is designed to meet the demanding or rigid performance requirements of education/schools, public premises, corporate, and industrial applications. GENERAL FUNCTION Display type: TFT-LCD MODULE DRIVE BOARD RESOLUTION:... -
Page 5: Connecting The Monitor
Adapter/Converter Advisory Should specific adapter/converter is required, i.e. tablet PCs, in order to connect to this monitor, please use original adapter/converter recommended by the original brand. The length of cables should not be longer than 2 meters each. 2 Connecting the Monitor The procedures for setting up your Monitor kit is as followed: Power &... -
Page 6: Using The Monitor
3 Using the Monitor 3.1 Get to know the monitor The Monitor connectors are located on the left side. They are shown in the physical monitor as figure below and described in the following paragraphs. Please note that connectors may vary in some derivative models; please refer to individual leaflet for special notation. - Page 7 3.3 Keypad Front View Bottom View Key Descriptions Key Name Operation Power Key Power On/Off Activates main OSD menu Navigates higher menu in main OSD menu Menu Key Stops auto frequency searching Exits OSD menu ...
-
Page 8: Remote Control
Remote Control The outlook of remote control is shown in the Figure, hereafter, Size: 90 x 40 x 12 mm Operation distance: ≤ 5 meter Working angle: not more then +/- 40 degree Product specification subject to change without prior notice. Page 8/41... - Page 9 IR-Remote controller Descriptions Key Name Description Power On/Off POWER Activates OSD menu of input source selecting SOURCE Navigates input source Displays input source information INFO Activates OSD of aspect ratio control ZOOM Toggles sound status of speaker MUTE ...
-
Page 10: Menu Overview
3.4 Content of OSD Menu 3.4.1 MENU OVERVIEW In this menu system, there are several ways to customize the menu settings provided. Most menus consist of three levels to set up the options, but some require greater depth for the variety of settings. -
Page 11: Basic Operation
3.4.2 BASIC OPERATION Turning On the Monitor First, connect power cord correctly. At this moment, the monitor switches to standby or power on mode. In standby mode, in order to turn monitor on, press the POWER button on the remote control. - Page 12 3.4.3 On Screen Menus Selection and Adjustment How to adjust the OSD screen Press the MENU button and then(◄/►)button to select each menu. Press the ENTER button and then use(▲/▼) button to display the available menus. Your monitor's OSD (On Screen Display) may differ slightly from what is shown in this manual. Product specification subject to change without prior notice.
-
Page 13: Select Video Input
3.4.4 SELECT VIDEO INPUT How to Select Video Source by OSD [PC-RGB, DVI, HDMI(1,2), HDMI3(UHD), USB, DP] Press the SOURCE button and then (▲/▼) button to select each video source. Press the ENTER button to go to desired video source Product specification subject to change without prior notice. -
Page 14: Picture Menu Options
3.4.5 PICTURE MENU OPTIONS Picture Mode Adjust the picture appearance to suit your preference and viewing situations. Press the MENU button and then (◄/►)button to select the PICTURE mode. Press the (◄/►)button and then use ENTER button to select Picture Mode menu. Standard, Dynamic, Mild, User ... - Page 15 Press the MENU button and then use (◄/►)button to select the PICTURE icon. Press the (▲/▼)button and then use ENTER button to select Color Temperature menu. Press the ENTER button and then use (◄/►)button to select desired option: User, Cool, Medium, Warm.
- Page 16 - Select the picture appearance to suit your preference and viewing situations. Press the MENU button and then (◄/►)button to select the PICTURE icon. Press the (▲/▼)button and then use ENTER button to select MFC menu Press the ENTER button and then use (▲/▼)button to select the desired picture option Off, Low, Middle, High &...
-
Page 17: Sound Menu Options
3.4.6 SOUND MENU OPTIONS Sound Standard Mode - Adjust the sound to suit your taste and room situations. Press the MENU button and then use (◄/►)button to select the SOUND icon Press the (▲/▼)button and then use ENTER button to select Sound Mode menu Standard, Music, Movie, Sports, User ... - Page 18 Press the MENU button and then use (◄/►)button to select the SOUND icon. Press the (▲/▼)button and then use ENTER button to select the Balance menu. Press (◄/►)button to make appropriate adjustments. [-50 ~ 0 ~ +50] ...
- Page 19 Volume - Adjust the sound to suit your taste and room situations. Press the MENU button and then use (◄/►)button to select the SOUND icon. Press the (▲/▼)button to select the Volume menu. Press ENTER button and then use (◄/►)button to make appropriate adjustments. [0 ~ 100] ...
-
Page 20: Setup Menu Options
3.4.7 SETUP MENU OPTIONS Language - Select a language for the menus to appear in. Press the MENU button and then use (◄/►)button to select the OPTION icon. Press the (▲/▼)button to select the OSD Language menu. ... - Page 21 Blending Adjusting the transparency of OSD. Press the MENU button and then use (◄/►) button to select the OPTION icon. Press the (▲/▼)button to select Blending menu Press the ENTER button to select the Details Menu. ...
- Page 22 DPMS Shut off the panel power after the input source has been unused for some time (idle), to save power. Press the MENU button and then use (◄/►)button to select the OPTION icon. Press the (▲/▼)button to select DPMS menu ...
- Page 23 3.4.8 TIME MENU Clock If current time setting is wrong, reset the clock manually. Press the MENU button and then use (◄/►)button to select the TIME icon. Press the ENTER button and then use (▲/▼)button to select Clock. ...
- Page 24 Off Timer Timer function operates only if current time has been set. Press the MENU button and then use (◄/►)button to select the TIME icon. Press the ENTER button and then use (▲/▼)button to select Off Timer. ...
- Page 25 3.5 USB 3.5.1 USB F/W Update (please call technical support) 3.5.2 USB Player Support Format Video Category Codec Supporting Maximum Resolution Bitrate MPEG1 MPEG1 MPEG2 MPEG2 MPEG-4 Visual DivX5 DivX4 DivX3 Up to 1920x1080 30 fps 20Mbps MPEG4 XviD MS-MPEG4 V3 MS-MPEG4 V2 WMV3 WMV2...
- Page 26 File Category Ext Supporting .avi .mpg .vob .rmv .rmvb .dat Video .mp4 .ogm .mkv .wmv .asf .flv .mov .jpg .bmp .gif Photo .png .tif Note: It will take a while to load data from your USB (USB Hard Drive). The more data in the hard disk are, time is the longer if read.
- Page 27 3.6 RS232 Command 3.6.1 Introduction This document is the communication protocol between the Monitor and PC Via RS232. 3.6.2 Data format Data will be transferred serially according to RS232 protocol using the following settings. MaleDB9DCEpinnumberinganddefinitions: recommended communication rates is 115200bps. Baud Rates 115200bps Data Bits...
- Page 28 3.6.4 Control Command Packet Data1 Data2 Data3 Data4 Data5 Description Range(HEX) Command Target Parameter Value English German Spanish French 0x00 Language Italian Dutch Russian Swedish Chinese PC-RGB HDMI 1 0x01 Source HDMI 2 4 HDMI 3 UHD 0x00~0xFF 0xF5 0x88 0x00 0xFE (By Min~Max)
-
Page 29: Cleaning The Monitor
4 Cleaning the Monitor 1. Make sure the monitor is turned off. 2. Never spray or pour any liquid directly onto the screen or case (depends on different model). 3. Do not use chemical solvents, alcohol, or any other based to clean the unit or panel. It may cause permanent damage on the unit or panel. - Page 30 6.4.2 Check if the signal timing of signal source (PC, IPC, and Laptop or media player) is within the specification of monitor. If you are unable to correct the fault by following this chart, stop using your monitor and contact your distributor or dealer for further assistance. ※Should all above trouble-shooting measure fails, please write down the S/N, Serial Number, which is located on the left-side of the monitor, and provide that S/N to the service personnel, this will help processing or further diagnosis easier.
- Page 31 8 Installation on Wall or Table Top (Optional Wall Mounts, Table Stands except 32” stand) I、32” Wall mount Installation guide Step 1 : Choose the siding appropriate for mounting. *The thickness of siding is 5 cm at least or above. *Please confirm the material and strength of the wall is appropriate to mounting.
- Page 32 Step 3 : Suspend the display on the hanging bracket. * Two adult prop up the display. * Put down the display slow on the hanging bracket. * Please confirm the hook with hanging plate to be joined on the hanging bracket. HANGING PLATE DISPLAY...
- Page 33 II、42”~ 55” Wall mount Installation guide Step 1 : Choose the siding appropriate for mounting. *The thickness of siding is 5 cm at least or above. *Please confirm the material and strength of the wall is appropriate to mounting. * Use the expansion bolts (B) to fix the hanging bracket (A) on the wall. Step 2 : Mounting the hanging plate (C) on the display.
- Page 34 * Two adult prop up the display. * Put down the display slow on the hanging bracket. * Please confirm the hook with hanging plate to be joined on the hanging bracket. Product specification subject to change without prior notice. Page 34/41...
- Page 35 III、65”~ 84” Wall mount Installation guide Step 1 : Choose the siding appropriate for mounting. *The thickness of siding is 5 cm at least or above. *Please confirm the material and strength of the wall is appropriate to mounting. * Use the expansion bolts (B) to fix the hanging bracket (A) on the wall. Step 2 : Mounting the hanging plate (C) on the display.
- Page 36 Step 3 : Suspend the display on the hanging bracket. * Two adult prop up the display. * Put down the display slow on the hanging bracket. * Please confirm the hook with hanging plate to be joined on the hanging bracket. Product specification subject to change without prior notice.
- Page 37 IV、32” Stand Installation guide Step 1：Open the package and to take out the stand. *Check the parts and that amount, please see the bellow picture. 1、32” Stand，1PCS 2、Screw M6*L10mm，6PCS Step 2：Mounting the display（A） on the stand. *Use screw（B） to fix the display on the stand（C）. B：M6*L10mm，...
- Page 38 V、42”~ 55” Stand Installation guide Step 1：Open the package and to take out the stand. *Check the parts and that amount, please see the bellow picture. 1、Stand，1PCS 2、Screw M6*L15mm，4PCS Step 2：Mounting the display（A） on the stand. *Use screw（B） to fix the display on the stand（C）. B：M6*L15mm，4PCS Product specification subject to change without prior notice.
- Page 39 VI、65”~ 70”Stand Installation guide Step 1：Open the package and to take out the stand. *Check the parts and that amount, please see the bellow picture. 1、Stand，1PCS 2、Screw M10*L25mm，4PCS Step 2：Mounting the display（A） on the stand. *Use screw（B） to fix the display on the stand（C）. B ：...
- Page 40 VII、84”Stand Installation guide Step 1：Open the package and to take out the stand. *Check the parts and that amount, please see the bellow picture. 1、80" Stand，1PCS 2、Screw M10*L25mm，4PCS Step 2：Mounting the display（A） on the stand. *Use screw（B） to fix the display on the stand（C）. C：M10*L25mm，4PCS Product specification subject to change without prior notice.
- Page 41 VIII、42"~84"Stand Assembly guide Step 1：Open the package and to take out the stand. *Check the parts and that amount, please see the bellow picture. 1、Stand R case， 2、Stand L case， 3、Stand B case， 4、Screw 1pcs﹒ 1pcs﹒ 1pcs﹒ M4*L8mm，4pcs﹒ Step 2：Use screw（A）to fix the stand B case between（B）and（C） ﹒ Stand B case Product specification subject to change without prior notice.