ABLE OF ONTENTS 1. BEFORE YOU BEGIN... 3 ... 3 HAT IS INCLUDED ... 3 NPACKING NSTRUCTIONS AC P ... 3 OWER ... 3 ONTACT ... 4 AFETY NSTRUCTIONS 2. INTRODUCTION ... 5 ... 5 EATURES DMX C ... 5 HANNEL UMMARY ...
Earth Ground. Contact Us W o r l d W i d e General Information Technical Support World Wide Web Multi Mover User Manual EGIN Chauvet Lighting 3000 North 29 Court Hollywood, FL 33020 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084...
Never disconnect the power cord by pulling or tugging on the cord. Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET at: 954-929-1115. Multi Mover User Manual 2007-01-03/16:45...
2. I NTRODUCTION Features • 4-channel DMX-512 media mover • Pan: 540° (ultra smooth) • Vector speed, power on/off and reset channel Ad d i t i o n a l F e a t u r e s • 3-pin and 5-pin DMX connections on base and platform •...
Product Overview Platform XLR In/Out Connector Edison Power Out Connector IEC Power Out Connector Voltage Selector Switch Base Back AC Power Switch Multi Mover User Manual Platform Front Platform Back Base Fuse Platform Fuse IEC Power Connector Base Front 5-pin DMX Output Connector Base...
Maximum recommended number of fixtures on a serial data link: 32 fixtures Data Cabling To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
3-PIN TO 5- PIN CON VE R SION CHAR T If you use a controller with a 5 Note! CHAUVET Model No: DMX5M, or DMX5F. The chart below details a proper cable conversion: IN TO ONVERSION Conductor...
(male) 3 pin connector. 3. Then, proceed to connect from the output as stated above to the input of the following fixture and so on. CHAUVET Certified DMX Data Cables Order Code Description DMX1.5 DMX Cable 1.5m/4.9ft DMX4.5...
Mounting ORIENTATION This fixture must be mounted horizontally. The base may be set on a flat surface or suspended. However, the base must always be parallel to the floor. R IG G IN G It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C”...
The Control Panel LED Display shows the menu items you select from the menu map on page 13. When a menu function is selected, the display will show immediately the first available option for the selected menu function. To select a menu item, press <ENTER>. Press the <MODE/ESC>...
Menu Functions PTION ESCRIPTION Stand Alone – Automatic: The built in programs will trigger automatically to a pre- programmed speed time. Slave Unit: Sets the fixture to run in sync with the Master. You must set the first fixture in the data link to “Master” otherwise nothing will happen. DMX: The fixture will be controlled by a DMX signal coming from a DMX controller.
Operation Stand-Alone Mode (Auto Mode): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode. Press <MODE/ESC> until Use the <UP> and <DOWN> buttons to scroll through until the press the <ENTER>...
DMX Mode This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with DMX, please read the DMX Primer on page #. Press <MODE/ESC> until Use the <UP> and <DOWN> buttons to select the desired address and press the <ENTER> button.
If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support at the location on the next page. Multi Mover User Manual...
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
DMX Channels ...4 Bandwidth (-3dB) RCA In/Out ... 85 MHz at Z XLR In/Out... 85 MHz at Z ORDERING INFORMATION Multi Mover ... M-MOVER WARRANTY INFORMATION Warranty ... 2-year limited warranty Multi Mover User Manual = 75 ohms = 75 ohms...