Table of Contents
Advertisement
Quick Links
Introduction:
IES308-2F are a smart plug-and-play industrial Ethernet
switch, which can provide economical solution for your Ethernet.
Its dustproof fully sealed structure(protective case of IP30 level),
over-current, over-voltage and EMC protected redundant double
power input as well as built-in intelligent alarm design can help
system main tenancy personnel monitor the network operation,
which can work reliably in harsh and dangerous environment.
IES308-2F supports 6 TP ports and 2 fiber ports(IES308-2F:
6-port 10/100Base-Tx, 2-port 100Base-FX). TP(RJ45)support
10/100Base-T(X), Full/Half duplex mode, and auto MDI/MDI-X
connection; 100BaseFX supports single-/multi-mode, SC/ST/FC
connector for optional.
Packing List:
The IES308-2F switch is shipped with following items.
1. Ethernet switch IES308-2F (plus terminal block)×1
2. Hardware Installation Guide ×1
3. Product Warranty Statement ×1
4. DIN-Rail setting fittings
Features:
1. Advanced Ethernet switch technical
2. IEEE802.3/802.3u/802.3x/802.3d,store and forward
3. 10/100M,F/H duplex, MDI/MDI-X auto negotiation
4. Broadcast storm protection
5. Relay output warning for power failure and port break alarm
6. Redundant 24VDC power input(12V～48VDC)
7. Designed for industrial applications. IP30 protection, rugged
high-strength metal case
8-port Unmanaged Industrial Ethernet Switch
Your Serial and Data Communications Expert
IES308-2F
Hardware Installation Guide
Shenzhen 3onedata Technology Co.,Ltd
Advertisement
Table of Contents
Related Manuals for 3One data IES308-2F
Summary of Contents for 3One data IES308-2F
- Page 1 IES308-2F supports 6 TP ports and 2 fiber ports(IES308-2F: 6-port 10/100Base-Tx, 2-port 100Base-FX). TP(RJ45)support 10/100Base-T(X), Full/Half duplex mode, and auto MDI/MDI-X connection;...
-
Page 2: Panel Layout
Your Serial and Data Communications Expert Panel Layout: IES308-2F(6 TP ports and 2 fiber port): Top panel Front panel Front panel 1. Grounding screw 2. Terminal block (4 bits) for PWR1/PWR2 Bottom panel input, terminal block (2 bits) for relay output 3. -
Page 3: Communication Connector
Your Serial and Data Communications Expert Units（mm） Communication connector: IES308-2F have 6 10/100BaseT(X) Ethernet ports(RJ45) and 2 100BaseFX (SC/ST/FC type connector) fiber ports. 10/100BaseT(X) Ethernet port The pinout of RJ45 port display as below, connect by UTP or STP. The connect distance is no more than 100m. 100Mbps is used 100Ωof UTP 5 , 10Mbps is used 100Ωof UTP 3,4,5. - Page 4 Your Serial and Data Communications Expert MDI signal MDI-X signal 4,5,7,8 — — Note: “TX±”transmit data±, “RX±”receive data±, “—”not use MDI(straight-through cable) RJ45 MDI-X(Cross over cable) RJ45 (RX+) (TX+) (RX-) (TX-) (TX+) (RX+) (TX-) (RX-) 100BaseFX port 100Base-FX full-duplex SM or MM port , SC/ST/FC type .The fiber port must be used in pair, TX (transmit) port connect remote switch’s RX(receive) port;...
-
Page 5: Led Indicator
Your Serial and Data Communications Expert LED Indicator: LED indictor light on the front panel of IES308-2F .the function of each LED is described in the table as below. System indication LED State Description PWR1 Power1 is being supplied to... -
Page 6: Relay Contact
The two wires attached to the Fault contacts form an open circuit when: (1) IES308-2F have lost power from one of the DC power inputs, One of the ports for which the corresponding Port alarm DIP Switch is set to ON is not properly connected. -
Page 7: Switch Settings
Storage Temperature: -45°C to 85°C Relative humidity 10% to 95% DIN-Rail Installation In order to use in industrial environments expediently,IES308-2F adopt 35mm DIN-Rail installation, the installation steps as fellows: 1. Examine the DIN-Rail attachment 2. Examine DIN Rail whether be firm and the position be suitability or not. -
Page 8: Wiring Requirements
Your Serial and Data Communications Expert Wiring Requirements： Be sure to disconnect the power cord before installing and/or wiring your Ethernet Switch. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. -
Page 9: Specifications
Your Serial and Data Communications Expert Specifications: Interface RJ45 Ports: 10/100BaseT(X) auto connection, F /H duplex or force work mode, and support MDI/MDI-X connection Fiber Ports: 100BaseFX ports (SC/ST/FC connector, optional) Single-mode: 20, 40, 60, 80, 100,120Km, optional Multi-mode: 2Km, optional Wavelength: 850nm, 1310 nm, 1550nm Alarm output interface：... - Page 10 Your Serial and Data Communications Expert EN61000-4-4(EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11 Shock: IEC 60068-2-27 Free Fall: IEC 60068-2-32 Vibration: IEC 60068-2-6 Warranty: 5 years Certifications: Shenzhen 3onedata Technology Co.,Ltd Tel: +86-755-26702668 Fax: +86-755-26703485 www.3onedata.com Shenzhen 3onedata Technology Co.,Ltd...