Table of Contents
Related Manuals for EEG HD490
Summary of Contents for EEG HD490
- Page 1 HD490 AFD Software Modular Add-On for HD490 Closed Caption Encoder EEG Enterprises, Inc. 586 Main Street Farmingdale, New York 11735 TEL: (516) 293-7472 FAX: (516) 293-7417 Copyright © EEG Enterprises, Inc. 2009-2012 All rights reserved.
-
Page 2: Table Of Contents
Copyright 2009-2011, EEG Enterprises, Inc. All rights reserved. The contents of this manual may not be transmitted or reproduced in any form without the written permission of EEG. The revision date for this manual is September 18, 2012. Copyright © EEG Enterprises, Inc. 2009-2011... -
Page 3: Introduction
HD490 AFD Software 1 Introduction 1.1 System Overview The EEG HD490 AFD Software is a flexible and versatile module running on the HD490 Closed Caption Encoder that encodes and recovers Active Format Descriptors (SMPTE 2016-1-2007). The HD490 can be used to statically insert any legal AFD code on each video field in HD VANC,... -
Page 4: Afd Code Reference
Pillarbox 14:9 image, horizontally centered 1011 Reserved 1100 Pillarbox 4:3 image, with alternative 14:9 center 1101 Full frame 16:9 image, with alternative 14:9 cen- 1110 Full frame 16:9 image, with alternative 4:3 cen- 1111 Copyright © EEG Enterprises, Inc. 2009-2011... -
Page 5: Using The Hd490 Afd Software
HD490 encoder to your local network. 2. Use the front panel LCD screen and button pad to set the HD490 IP address and subnet mask. These must be valid settings for your network, or you will not be able to communicate with the encoder. - Page 6 HD490 AFD Software Figure 1: AFD module web browser configuration page Copyright © EEG Enterprises, Inc. 2009-2011...
-
Page 7: Settings On The Configuration Panel
3.2 Settings on the Configuration Panel The web-based configuration page controls the input and output behav- ior of the HD490 AFD tool. You must press the Apply button before any configuration changes take effect. You can press the Revert button at any time to before pressing Apply to cancel the changes that have not gone into effect yet. -
Page 8: Output Setup
3.2.3 Data Continuity VANC This field sets the number of frames that the HD490 will continue out- putting an AFD code from an upstream VANC source if that source stops sending AFD data. This feature can be used to ensure that AFD data will be encoded on every frame at the output even if an upstream source is only encoded on same frames. -
Page 9: Preset Default
HD490 AFD Software This field sets the number of frames that the HD490 will continue out- putting an AFD code from an upstream XDS source without seeing any new upstream XDS packets. This feature is critical for use of the XDS recovery feature because XDS cannot be sent on every frame due to Line 21 bandwidth limitations. -
Page 10: Add Code Swap Rules
Remove button. To delete a code swap rule, go to the line in the table where the swap rule is and click the Remove button to the right of the code swap rule. Copyright © EEG Enterprises, Inc. 2009-2011... -
Page 11: Network Automation Protocol
A Appendix A A.1 Network Automation Protocol HD490 software modules can be remotely controlled over a network by connecting to TCP port 2300 on the encoder. The messages sent to this port from any automation server must follow the format given in this appendix. - Page 12 TCP packet of the same format. The 4-byte status code will be set to 0 to indicate success, and a non-zero value to indicate an error in parsing or executing the command. The data string will be empty. Copyright © EEG Enterprises, Inc. 2009-2011...