Advertisement
4. asseMbly
4.1.
Assemble four wheels with nuts, spring washer, washers, and bolts. ensure that the
two locking wheels are at the same end.
4.2.
remove extension arm (fig1.c) from main beam undoing knob (A) and lifting arm off.
4.3.
Assemble main beam (c) to wheel frames by fixing with four bolts, spring washers,
washers and nuts at each end (B).
4.4.
check that all connections are tight and replace the extension arm (c) by screwing
knob (A) into the holding plate set inside the frame of the main beam.
4.5.
screw the appropriate supports into the end of the extension arm at point (X) and place
the unused supports in their storage eyes (d).
WarnInG! Before use ensure section 1 safety instructions are read and understood.
‰
4.6.
check and prepare the vehicle as mentioned in the safety instructions ensuring the ground
on which the trolley is to travel is level and solid (not tarmacadam).
4.7.
Position the trolley supports under the vehicle manufacturer's recommended lifting point. if using the sill clamps ensure
they are correctly fitted and tightened. check that the vehicle is secure and there are no persons or obstacles beneath
the vehicle or in the path of transportation. ensure the wheel brakes are unlocked and move the vehicle.
4.8.
When the trolley destination is reached, the trolley wheel brakes must be applied to stop further movement.
Do not use trolley as a support stand for working on, or under, the vehicle. the trolley is designed for manoeuvring only.
5. MaIntenance
5.1.
Before each use check for broken, cracked, bent, or loose parts, or any visible damage. if any suspect item is found remove trolley
from service and take necessary action to remedy the problem.
Do not use the trolley if believed to have been subjected to abnormal load or shock load.
5.2.
Keep the trolley clean and periodically oil the wheel bearings.
6. parts DIaGraM
7.
Item part no
Description
1
re901/01 screW m6x10
2
re901/02 PressinG BoArd
3
re901/03 dePression BAr
4
re901/04 PressinG BoArd
5
re901/05 Bolt m12x35
6
re901/06 WAsHer
7
re901/07 sPrinG
8
re901/08 nut m12
9
re901/09 BeArinG Post
10
re901/10 Bolt m12x70
11
re901/11 WAsHer
12
re901/12 Bolt m10x25
13
re901/13 GriP
14
re901/14 sPrinG Pin
15
re901/15 screW
16
re901/16 locAtinG AdAPtor
17
re901/17 BlocK
18
re901/18 moVABle BeAm
19
re901/19 crossBeAm
20
re901/20 suPPort BeAm
21
re901/21 sPrinG WAsHer
22
re901/22 nut m10
23
re901/23 Bolt m8x20
24
re901/24 WAsHer
25
re901/25 nut m8
26
re901/26 cAstor AssemBlY
recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMportant: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
part
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
environmental protection
01284 757500
01284 703534
fig.2
www.sealey.co.uk
sales@sealey.co.uk
re901 | issue 3(i) 10/04/17
Advertisement
