Advertisement
2. INTRODUCTION & SPECIFICATION
Features tilt and swivel head for optimum air circulation. Touch pad/Remote control operation and fully guarded fan blades to BS5060/IEC879
for ease of use and extra safety. Smooth running motor powers both fan blades and electronically operated oscillating gearbox for even air
distribution. Timer function allows preset running time between 30 minutes and 7.5 hours. Features three modes - Normal, Nature and Sleep.
Nature mode for alternate strong and weak intensities of circulating air. Sleep mode for gradual reduction in intensity of circulating air.
Max Air Flow . . . .68mtr
/min
3
Supply . . . . . . . . .230V 50Hz 40W
Height . . . . . . . . .1090 - 1390mm
3. ASSEMBLY
Unpack carton and assemble the fan as follows:
3.1.
Fix pole (fig 1.1) to base (fig 1.4) using four screws (fig 1.3) and slide base cover (fig 1.2) over base .
3.2.
Fit head unit onto top of pole and secure by tightening knob at base of head.
3.3.
Remove the locking nut (fig 2.1) from the centre of the fan.
3.4.
Fitting the rear fan guard. Identify the rear fan guard by the location holes in the centre plate (fig 2.2)
and place the guard over the fan spindle and fit onto the three location pins (fig 2.3.).
3.5.
Replace and secure the back guard with locking nut (fig. 2.1).
3.6.
Fitting the fan. Slide the fan onto the motor shaft until it comes to rest against the pin which is pushed through the shaft. Rotate the fan
slightly until the pin comes to rest in the shallow groove in the back of the fan. Now take the large plastic circular lock nut and thread it
onto the end of the motor shaft by turning it anticlockwise. Hold one of the fan blades with one hand and tighten the nut down onto the
fan to hold it in place.
3.7.
Fitting the front fan guard to the rear fan guard. The front guard has a metal clip attached to it which enables it to hook over the top of
the rear guard (fig 3.A) and a screw fix at the bottom (fig 3.B).
3.8.
When the metal clip has been hung on the top and the screw attached in the bottom, slide the four clips on the front cover down so they clip to
the rear guard.
If all is correct the fan is now ready to use.
4. OPERATION
WARNING! Ensure you read, understand and apply the safety instructions in part 1 before using the fan.
!
4.1.
Place the fan in a suitable location on a level surface. Plug into the mains power supply.
4.2.
Adjust tilt, direction and height of fan as required.
4.3.
Using either the remote control or the buttons on the fan, press the power button to switch the fan on.
4.4.
Adjust the fan speed by pressing the speed button. The sequence is Low - Medium - High.
4.5.
Set the timer by pressing the timer button. The timer can be set between 30 minutes and 7 hours 30 minutes. Each press increases the
time by 30 minutes and is indicated by the appropriate lights.
Note: depending on time selected, more than one light may light up - add together the lit up times to reach the time set.
4.6.
To make the fan oscillate, press the oscillating button. To stop the fan oscillating, press the button again.
4.7.
MODES: The fan has three mode settings, these are selected by pressing the Mode button. The three modes are:
Normal, Nature and Sleep.
4.8.
Normal is a constant speed.
4.9.
Nature is an alternating fast / slow speed.
4.10.
Sleep is the same as Nature initially, then after 30 minutes the fan speed will gradually decrease.
5. CARE OF FAN
IMPORTANT: Turn the fan OFF and disconnect from power supply before cleaning.
5.1.
Use only a soft, damp cloth to clean the fan.
5.2.
DO NOT submerse the fan in water and NEVER allow water to drip into the motor housing.
5.3.
DO NOT use solvents or other chemicals to clean the fan.
5.4.
To clean the fan blades, remove front guard - reverse of assembly procedure 3.7. above.
5.5.
Wipe the blades and guards clean.
5.6.
Reassemble front guard following assembly procedure 3.7. and 3.8. above.
5.7.
Store the fan in its original box or otherwise cover the fan to protect it from dust.
Declaration of Conformity
Pedestal Fan 3 Speed 16"
Model: SPF16WR
98/37/EC Machinery Directive
89/336/EEC EMC Directive
73/23/EEC Low Voltage Directive
93/68/EEC Marking Directive
2002/95/EC RoHS Directive
2002/96/EC WEEE Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
Fan Diameter . . . .400mm
Speeds . . . . . . . .3
Modes . . . . . . . . .Normal, Nature, Sleep
We, the sole importer into the UK, declare that the product listed below is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected on request by contacting Jack
Sealey Ltd
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
fig 2
01284 757500
01284 703534
fig 1
fig 3
For Jack Sealey Ltd.
1st February 2007
Sole importer into the UK
of Sealey Power Products
www.sealey.co.uk
Web
sales@sealey.co.uk
email
1
2
3
4
SPF16WR - 1 - 190307
Advertisement
