Advertisement
Quick Links
Operation Manual
AOYUE INT 866 Rework Station
90866
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec AOYUE INT 866
Summary of Contents for WilTec AOYUE INT 866
- Page 1 Operation Manual AOYUE INT 866 Rework Station 90866 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Temperature range ( 100–480 (212 °F–869 °F) Heating element Metal core heating Pump/motor type Sirocco ventilator Pre-heater Power consumption (W) ℃ Temperature range ( 100–480 (212 °F–869 °F) Heating element Quartz crystal © by WilTec Wildanger Technik GmbH Item 90866 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 4 * The various soldering tips included in the delivery may vary depending on the availability. T-I is already placed in the soldering iron. ** Please refer to the assembly instructions for the parts and instructions of the soldering iron stand. © by WilTec Wildanger Technik GmbH Item 90866 Page 4 http://www.WilTec.de...
- Page 5 Soldering work creates smoke. Thus work in a well ventilated area. Do not alter the device in any way, especially not the inner circuit. © by WilTec Wildanger Technik GmbH Item 90866 Page 5 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 6 To install the stand of the heating gun: Use the 8 mm screw, to attach the holder to the station. Place the heat gun on the holder in preparation for use. © by WilTec Wildanger Technik GmbH Item 90866 Page 6 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 7 … soldering iron/activation of the outer sensor Meanings of the abbreviations Abbr. Meaning Abbr. Meaning External sensor Cooling down Actual temperature Display standby Temperature adjustment OFF Display function deactivated © by WilTec Wildanger Technik GmbH Item 90866 Page 7 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 8 90 ℃ . In this time, the abbreviation on the display of the heat gun will change from “H” to “C” whilst the temperat - © by WilTec Wildanger Technik GmbH Item 90866 Page 8 http://www.WilTec.de http://www.aoyue.eu...
- Page 9 90 ℃ , the heat gun will stop automatically. The display will show “---,” meaning that the system is in standby mode. © by WilTec Wildanger Technik GmbH Item 90866 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 10 (“OFF” is shown on the displays 1 and 2), hold the pre-heater “up” button for a few seconds until “0000” is shown on the display. 6. Adjust the temperature compensation via the “up” and “down” buttons on the soldering iron settings. © by WilTec Wildanger Technik GmbH Item 90866 Page 10 http://www.WilTec.de http://www.aoyue.eu...
- Page 11 2. The soldering tip is damaged and needs to be exchanged. 3. The device will show “PLUG”: Sign of a problem with the contacts of the sol- dering iron or the tip. © by WilTec Wildanger Technik GmbH Item 90866 Page 11 http://www.WilTec.de...
-
Page 12: Troubleshooting
The device is being reset to factory set- tings. With any other problems, please contact a specialist. © by WilTec Wildanger Technik GmbH Item 90866 Page 12 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de... - Page 13 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.