Casio Baby-G BG1001-1V Operation Manual page 2

Operation Guide 3035
To cancel a preset timer operation
In the Timekeeping Mode, hold down D for about two seconds.
Graphic Area
When the end of a countdown is reached, the graphic
Graphic
area will flash for 10 seconds or until you press any
button.
The table below shows how the graphic area indicates the
displayed preset start time and the remaining number of
minutes left in the countdown.
• The graphic area indicates the amount of countdown
time remaining no matter what mode the watch is in.
Graphic
Preset Start
Time 01'00 02'00 03'00 05'00 10'00 15'00 20'00 30'00 45'00 60'00
Remaining 00'01 01'01 02'01 03'01
Countdown – – – –
Time 01'00 02'00 03'00 05'00
World Time
World Time shows the current time in 48 cities (29 time
City code zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time for another city code
In the World Time Mode, press D to scroll eastwardly
through city codes or B to scroll westwardly.
• For full information about city codes, see the "City Code
Current time in the zone
Table".
of the selected city code
• If the current time shown for a city is wrong, it could
mean that the Timekeeping Mode time or Home City
code settings is wrong. Check these settings and make
the necessary changes.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D and B to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about one second to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
DST indicator
turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
• In the World Time Mode, you can switch the city code
you currently have selected as your Timekeeping Mode
Home City between Standard Time and DST. The
setting you select in the World Time Mode will also be
applied in the Timekeeping Mode.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes,
59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Minutes
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
Seconds
elapsed time measurement.
1/100 second
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Start Stop Re-start
Split Time
Start Split Split release
( displayed)
Two Finishes
Start Split Stop
First runner Second runner
finishes. finishes.
Display time of
first runner.
05'01 10'01 15'01 20'01 30'01 45'01
– – – – – –
10'00 15'00 20'00 30'00 45'00 60'00
Stop Clear
Stop Clear
Split release Clear
Display time of
second runner.
Alarms
You can set five independent Daily Alarms. When an
Alarm number
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
through
On/Off status
), and one is for the Hourly Time Signal (indicated
by ).
Alarm time
• All of the operations in this section are performed in the
(Hour : Minutes)
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D and B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
• To set a one-time alarm, display one of the screens
indicated by an alarm number from
. To set the snooze alarm, display the screen
indicated by
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D and B to select an alarm.
Snooze alarm indicator 2. Press A to toggle it on (
( displayed).
• Turning on a one-time alarm (
displays the alarm on indicator on its Alarm Mode
screen.
• Turning on the snooze alarm (
on indicator and snooze alarm indicator on the Alarm
Mode snooze alarm screen.
• The alarm on indicator is displayed in all modes when
any one of the alarms is turned on.
On/Off status
• The alarm on indicator flashes while the alarm is
Alarm on indicator
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D and B to select the Hourly
On/Off status
Time Signal (
2. Press A to toggle it on (
( displayed).
• The Hourly Time Signal on indicator is shown on the
display in all modes while the Hourly Time Signal is
turned on.
Hourly time signal
on indicator
), one is for a snooze alarm (indicated by
Press .
Press .
through
.
displayed) and off
through )
) displays the alarm
).
displayed) and off
2