Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Solid Technologies ALLIANCE PS2ROU
Summary of Contents for Solid Technologies ALLIANCE PS2ROU
- Page 1 ALLIANCE_PS2ROU User Manual Confidential & Proprietary 1/27...
- Page 2 REVISION HISTORY No. of Version Issue Date Initials Details of Revision Changes Pages V 1.0 Sep. 01, 2019 Original Technical Support SOLiD serial numbers must be available to authorize technical support and/or to establish a return authorization for defective units. The serial numbers are located on the back of the unit, as well as on the box in which they were delivered.
-
Page 3: Table Of Contents
Contents Section1 Safety & Certification Notice ............... 5 Section2 System configuration and Functions ............. 8 2.1 PS2ROU (Public Safety 2W Remote Unit) ............8 2.1.1 Specifications of PS2ROU ................9 Block Diagram of PS2ROU ................. 10 2.1.2 2.1.2.1 PS2ROU block diagram ................10 2.1.2.2 ROU inner look.................. - Page 4 Contents of Figure Figure 3. PS2ROU ....................8 Figure 4. PS2ROU outer Look ................9 Figure 5. PS2ROU Block diagram ............... 10 Figure 6. Inside of Remote Unit ................. 11 Figure 7. PS2RDU Outer Look ................13 Figure 10. R OPTIC Outer Look ................17 Figure 11.
-
Page 5: Safety & Certification Notice
Section1 Safety & Certification Notice “Only qualified personnel should handle the DAS equipment. Any person involved in installation or service of the DAS should understand and follow these safety guidelines.” - Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. - Page 6 - For pluggable equipment, make sure to install the socket outlet near the equipment so that it is easily accessible. - A readily accessible disconnect device shall be incorporated external to the equipment. - This power of this system shall be supplied through wiring installed in a normal building. If powered directly from the mains distribution system, it shall be used additional protection, such as overvoltage protection device - Only 50 ohm rated antennas, cables and passive equipment shall be used with this remote.
- Page 7 Prior to equipment use the service must be registered with the FCC. This can be done through the FCC’s website at https://signalboosters.fcc.gov/signal-boosters. - Certification FCC: This equipment complies with the applicable sections of Title 47 CFR Parts 90(Class B) - Use of unauthorized antennas, cables, and/or coupling devices not conforming with ERP/EIRP and/or indoor‐only restrictions is prohibited.
-
Page 8: System Configuration And Functions
Section2 System configuration and Functions 2.1 PS2ROU (Public Safety 2W Remote Unit) PS2ROU receives TX optical signals from ODU and converts them into RF signals. The converted RF signals are amplified through Power Amp in a corresponding PS2RDU band combined with UDCU, PAU and Cavity Filter, and then radiated to the antenna port. -
Page 9: Specifications Of Ps2Rou
2.1.1 Specifications of PS2ROU Figure 2. PS2ROU outer Look Spec. Remark Item PS2ROU 700PS_FN +33dBm 800PS +33dBm The rated mean output Power per band VHF/UHF +24dBm 900I_PA +33dBm FCC : 758~775MHz 700PS_FN 17MHz ISED : 758~775MHz FCC : 851~861MHz The nominal downlink 800PS 10MHz bandwidth... -
Page 10: Block Diagram Of Ps2Rou
ISED : 406.1~430MHz 450~470MHz FCC : 929~930MHz 935~940MHz ISED : 929~930MHz 900I_PA 6MHz 932~932.5MHz 932.5~935MHz 935~940MHz 700PS_FN 17MHz 788~805MHz 800PS 10MHz 806~816MHz The nominal Uplink bandwidth 80MHz 136~216MHz 132MHz 380~512MHz 900I_PA 6MHz 896~902MHz 2.1.2 Block Diagram of PS2ROU 2.1.2.1 PS2ROU block diagram Figure 3. -
Page 11: Rou Inner Look
2.1.2.2 ROU inner look Figure 4. Inside of Remote Unit ** In the HARU enclosure, not need to install R-Optic Confidential & Proprietary 11/27... -
Page 12: Ps2Rou Part List
2.1.2.3 PS2ROU part list Unit Description Remote Drive Unit Amplify TX signals PS2RDU Amplify RX signals Remove other signals through BPF Remote AC Power Supply Unit RPSU (AC) Input power: 100~240 VAC Output power: +29.2 VDC Remote DC Power Supply Unit RPSU (DC) Input power: -42 ~ -56 VDC Output power: +29.2 VDC... -
Page 13: Function By Unit
2.1.3 Function by unit 2.1.3.1 Public Safety 2W Remote Drive Unit (PS2RDU) When receiving TX signals from each band throughgh Remote Optic, PS2RDU filters the signals and amplifies them with High Power Ampifier. The unit also filters RX signals given throughgh amplifies them to send the signals to Remote Optic.In the unit, there is ATT to adjust gain. - Page 14 ISED : 758~775MHz 800PS > FCC : 851~861MHz ISED : 851~861MHz FCC : 929~930MHz 935~940MHz ISED : 929~930MHz PS2RDU_90I_PA Single band 896~902MHz 932~932.5MHz 932.5~935MHz 935~940MHz Confidential & Proprietary 14/27...
-
Page 15: Ps2Rou Power Supply
2.1.3.2 PS2ROU Power Supply AC Power Supply The PS2ROU supports only AC 100~240V input power and only a single type of power cable is provided. The pin discription of AC port is as below. Pay attention to the correct polarity. Check if the connection is the same as one seen in the table above and make sure to turn the power ON. -
Page 16: Remote Optic(Roptic)
DC Power The N2ROU supports only DC -48V input power and a single type of power cable is provided. The pin discription of DC port is below. Pay attention to the correct polarity. Check if the connection is the same as one seen in the table above and make sure trn the power ON. -
Page 17: Remote Central Processor Unit (Rcpu)
Figure 6. R OPTIC Outer Look 2.1.3.4 Remote Central Processor Unit (RCPU) RCPU can monitor and control each module of PS2ROU. This unit receives and analyzes upper communication data from Remote Optic and reports the unit's own value to upper devices. At the front of the module, it has LED indicator to show system status, letting you check any abnormalities at a time. -
Page 18: Multiplexer
2.1.3.5 Multiplexer Multiplexer it called combine unit(CU) works as a module to combine or distribute multiple signals into one or two antennas. This device has a port to combine multiple signals. You need to connect input and output ports of RDU throughgh a corresponding port. -
Page 19: Bottom Of Ps2Rou
2.1.4 Bottom of PS2ROU 2.1.4.1 Functions Figure 9. The Bottom Look of PS2ROU Port PS2ROU Remark SC/APC, Waterproof Optical Port Optiacl Input port Power Port The cable is directly inserted in port hall. VHF/UHF Port VHF/UHF Tx port and VHF/UHF Rx Port Antenna port DIN to N type 6 External alarm has been located in bottom... -
Page 20: Section3
Section3 System Installation 3.1 PS2ROU Installation This chapter describes how to install each unit and optical cables, along with power cabling method. In detail, the chapter describes how to install shelves or enclosuers of each unit, Power Cabling method and Optic Cabling and RF Interface. Furthermore, by showing power consumption of modules to be installed in each unit, it presents Power Cabling budget in a simple way. -
Page 21: Ps2Rou Enclosure Installation
3.1.2 PS2ROU Enclosure installation PS2ROU is designed to be water- and dirt-proof. The unit has the structure of one-Body enclosure. It satisfies water-proof and quake-proof standards equivalent of UL Type4X. The way to install for both PS2ROU has same method. Basically PS2ROU is attached with wall mountable bracket. PS2ROU can be mounted into either of wall or on a pole. -
Page 22: Ps2Rou Wall Mount Installation
Figure 11. Dimension used to install PS2ROU on the WALL 3.1.3 PS2ROU Wall Mount Installation PS2ROU’s installation bracket is attached on Enclosure when is delivered. It doesn’t need to remove bracket to install enclosure. simply after installing 4 of M12 mounting bolts, secure 4 mounting bolts tightly. -
Page 23: Ps2Rou Components
3.1.4 PS2ROU components PS2ROU has the following components: Unit Description Remark Enclosure Including Wall mounting bracket RCPU R_OPTIC With SC/ACP adaptor 1EA,optional Common RPSU AC 100~240V or DC -48V Part This integrated combiner unit combines all bands 1EA, CU-70P80P90I for output to a single antenna connection. optional Power Cable The cable is directly inserted in port hall... -
Page 24: Ps2Rou Optical Cable
3.1.4 PS2ROU Optical Cable The Optical Connector is located at the bottom of Remote Unit enclosure fixed. Optical Cable can be connected by using connectors. The specification of compression Optic Connector is like below. The way to install the Optical cable comply with below procedures The procedures are Figure 12. -
Page 25: Ps2Rou Alm In/Out Port Cabling
3.1.5 PS2ROU EXTERNAL ALM IN/OUT Port cabling The ALM IN/OUT Connector is located at the bottom of Remote Unit enclosure fixed. Cable can be connected by using connectors. Figure 13. Location of ALM IN/OUT Connector 3.1.6 Mounting of PS2RDU PS2ROU has slots to enable up to four PS2RDU modules to be mounted in it. You can mount a PS2RDU into designated slot surely and should install each PS2RDU into its designated location as shown in the installation diagram on the door of enclosure. - Page 26 FCC/IC User Warning FCC PART 15.105 STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 27 RSS-GEN, SEC. 7.1.2 – (DETACHABLE ANTENNAS) This radio transmitter (identify the device by certification number, or model number if Category II)has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Need help?
Do you have a question about the ALLIANCE PS2ROU and is the answer not in the manual?
Questions and answers