Advertisement
4. OperatiON
4.1.
ZerO settiNg
4.1.1.
Prior to operation, perform a zero setting. to do this close the jaws (fig1.1.) then press the 'Zero' button (fig1.4.); the gauge has been set
to zero when the lcd displays '0.00'.
note: After zero setting, the gauge retains this setting until the 'Zero' button is pressed again or the battery is removed.
4.2.
ensure all surfaces are clean before measuring.
4.3.
switch on the gauge by pressing the on/off button (fig.1.3.) and set units using unit selector button (fig1.6).
4.4.
for disc measurement: open the external jaws to clear the lip and close onto the disc surface. the reading may be saved by pressing the
Hold Button (fig1.5), allowing withdrawal over the lip. A second press returns to the current reading.
4.5.
for drum measurement: extend the internal jaws until they meet the inner surface of the drum.
4.6.
the use of excessive force will lead to inaccurate measurement and damage to the gauge.
fig.1
5. maiNteNaNce
5.1.
batterY iNstallatiON/replacemeNt (fig.2)
NOte: the battery should last for one year of continuous use.
5.2.
if the display is blank or the digits are flashing the battery voltage is too low, replace the battery with a new sr44 battery. if the digits
do not change when buttons are pressed or probe is moved, remove the battery for 1 minute to reset the unit. the battery should be
removed if the gauge is not to be used for a long period of time.
5.3.
remove battery cover by sliding backwards and lifting off.
5.4.
remove exhausted battery and fit replacement with +ve side uppermost. Place the battery into the recess and press into place. slide the
cover back and click home.
5.5.
dispose of old battery in a safe and approved manner.
eNVirONmeNt prOtectiON
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Weee regulatiONs
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic equipment
(Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid
waste authority for recycling information.
batterY remOVal
see section 4.1. under the Waste Batteries and Accumulators regulations 2009, Jack sealey ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak's registered
compliance scheme. Jack sealey ltd Batteries Producer registration number (BPrn) is BPrn00705.
Note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
sealey group, kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar
01284 757500
© Jack sealey limited
keY
1:. . . . . . . . . . . . . . . . . internal Jaws
2:. . . . . . . . . . . . . . . . external Jaws
3:. . . . . . . . . . . . . . . . on/off Button
4:. . . . . . . . . . . . . . . . . . Zero Button
5:. . . . . . . . . . . . . . . . . . Hold Button
6:. . . . . . . . . . . unit selector Button
7:. . . . . . . . . . . . . . . . . . lock screw
8:. . . . . . . . . . . . . . . . Battery cover
01284 703534
sales@sealey.co.uk
Original Language Version
fig.2
www.sealey.co.uk
Vs0566| issue:2 (l) 19/10/17
Advertisement
