Flann Microwave Model 625 1 GENERAL INFORMATION 1.1 WARRANTY Flann Microwave Ltd warrants each product of its manufacture to be free from defects in material and workmanship. Our obligation under this warranty is limited to servicing or adjusting any products returned to our address for that purpose, and to make good at our facility any part or parts thereof, ...
Flann Microwave Model 625 2 GETTING STARTED Plug an Ethernet cable into an Ethernet switch, router or adaptor capable of providing Power‐over‐ Ethernet (PoE) to IEEE 802.3af, and connect the other end to the 625 instrument. The Ethernet interface is provided by a Lantronix xPICO 110 device. Under no circumstances should this device be re‐configured. In the event that the label showing the instrument MAC address is accidentally removed from the ...
Flann M Microwave Mod del 625 2.2 M MANUAL IN NTERFACE E The scr reen displays the current position and d the target position and has icons to o signify whe en it is receivin ng a remote co ommand or a a state save is taking place. The cen ntral button h as three distin nct functions ...
Flann Microwave Model 625 3 ENVIRONMENTAL CONSIDERATIONS The Model 625 System Attenuator is designed to operate in ‘non‐hazardous’ indoor industrial or laboratory areas, or in a protected outdoor environment. The operating environment must conform to the conditions shown in Table 1. Operation outside these ranges cannot be guaranteed and may pose dangers to the operator or cause mechanical or electrical . ...
Flann Microwave Model 625 4 SYSTEM FUNCTIONS AND FEATURES 4.1 POWER‐UP PROCEDURE When the instrument is connected to a PoE‐compatible network, it resets to the 60 dB reference position. This action may be disabled if required, but the instrument must be reset as soon as possible to establish the correct reference alignment. Refer to the ‘PWR_ON_RST’ and ‘RESET_INST’ commands in section 5.2. The instrument is supplied with ‘PWR_ON_RST’ set to ON. The instrument can be programmed to return to the last setting prior to power being removed. Refer to the ‘HOLD_SET’ command. 4.2 SETTING ATTENUATION The instrument can be set to attenuation values in the range 0.0 dB to 60.0 dB using the VALUE_SET command. The smallest incremental value depends on the absolute attenuation: 0.01 dB (up to 20dB ...
Flann Microwave Model 625 When the high attenuation setting is active, this enables a coarse attenuation setting of up to 90 dB. Refer to the ‘HIGH_ATTEN’ command. The attenuation accuracy beyond 60 dB is not guaranteed. The front panel display colours are inverted when the attenuation is set to a value greater than 60 dB. 4.3 INSTRUMENT ERRORS Instrument errors can be identified by interrogating the Status Byte (see information for the ‘INST_STAT?’ in section 5.2, and refer to Table 3). 4.4 FIRMWARE UPGRADES Users will be able to upgrade to the latest version of the Model 625 firmware over the Ethernet interface by following the instructions given on the Flann Microwave Ltd website, www.flann.com. A copy of the latest issue of this manual will also be available for download. ...
Flann Microwave Model 625 5 ETHERNET COMMAND STRUCTURE This section details the commands available and the valid operands that may be used with them. 5.1 NOTATION Upper case bold characters represent the (program code) commands, which must appear exactly as listed. Program code commands are not case sensitive, i.e. upper and lower case characters are accepted. The input buffer is 50 bytes maximum. Characters enclosed in the {} brackets are qualifiers attached to the basic command. A space may be inserted between it and basic command, e.g. {ON|OFF} shows that either ON or OFF can be attached to the root mnemonic. For example, the ‘PWR_ON_RST’ command has three possible applications: 1. PWR_ON_RST ON ‐ Switch on the Power‐on Reset 2. PWR_ON_RST OFF ...
Page 11
Flann Microwave Model 625 STORE_VAL value Sets the stored setting to value Query: Valid, returns stored setting Value 0 to 60.0 (dB) REC_SETTING Sets the instrument to the stored setting (dB) Query: Invalid HIGH_ATTEN {ON|OFF} Sets the high attenuation feature on or off Query: Valid, returns 1 for on, or 0 for off The front panel display colours are inverted when the attenuation is set to a value greater than 60 dB. HOLD_SET {ON|OFF} Returns the microwave instruments to the position when power was removed Query: Valid, returns 1 for on, or 0 for off PWR_ON_RST {ON|OFF} Enables or disables the Power‐on reset Query: Valid, returns 1 for on, or 0 for off RESET_INST Re‐synchronise the instrument by driving to the reference position of 60.0 dB. This is the software ...
Flann Microwave Model 625 5.3 STATUS BYTE Bit Value Error 0 1 EEPROM error – failure to read or write to the EEPROM 1 2 Out of range request – incorrect value requested 2 4 Power on – a power‐on has occurred since the last read of the register 3 8 Command error – incorrect syntax in a command line 4 16 Execution error – failure to achieve setting 5 32 Not used 6 64 Error E2 – no encoder output found 7 128 Error E1 – encoder index not found Table 3 – Status Byte interpretation Note: The value of the Status Register will return to zero after being read. 5.4 COMMAND SUMMARY ...
Flann Microwave Model 625 5.5 EXAMPLES RESET_INST\n reset the instrument VALUE_SET?\n returns a value of 60 VALUE_SET23.4\n position to 23.4 dB VALUE_SET?\n returns the value 23.4 STEPS_SET453\n switch to steps mode and position to 453 STEPS_SET?\n returns the value 453 INCR_SET10\n ...
Model 625 6 CARE OF THE INSTRUMENT Internally, the 625 System Attenuator is a delicate instrument. When the waveguide ports are not connected, it is recommended that flange covers (such as supplied with the instrument) are fitted. This will help prevent inadvertent damage to the flange surfaces and internal vanes, and prevent dust from entering the waveguide structure. ...
Page 15
Flann M Microwave Mod del 625 7 REG GULATO RY INFOR RMATIO 7.1 D ECLARATI ION OF CO ONFORMI ITY Model 62 25 Versio on 1.2 June 20 Page 15 of 16 ...
Flann Microwave Model 625 7.2 WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) REGULATIONS Flann Microwave is registered with the United Kingdom Environment Agency as a supplier of electrical and electronic equipment, and makes the required declarations in accordance with WEEE Regulations. Where this product was supplied to a customer in the United Kingdom: When this product is at the end of its life, Flann Microwave will accept its return for safe disposal and ...