1. Manuals
  2. Brands
  3. LaCoSys Manuals
  4. Modulator
  5. SmartPower XS 10-2
  6. Manual

LaCoSys SmartPower XS 10-2 Manual

Laser current source with tec-temperature control
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SmartPower XS 10-2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for LaCoSys SmartPower XS 10-2

Summary of Contents for LaCoSys SmartPower XS 10-2

  • Page 2 Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 MANUAL SMART-POWER XS LASER CURRENT SOURCE WITH TEC-TEMPERATURE CONTROL Made in Germany by 2-11 SmartPower XS 10-2 LaCoSys Sept 2020 Rev. A...
  • Page 3 Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 FEATURES  Laser driver for butterfly-14-Pins LC96 package  Integrated PI- control loop for laser built in Peltier element  Wide input voltage range ...

  • Page 4: Table Of Contents

    Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Contents Introduction ................................4 Technical Parameters ............................5 Mechanical Drawing ............................. 6 Pin & jumper description ............................7 Laser Diode connection ............................9 Getting Started ..............................10 Hardware Setup ............................

  • Page 5: Technical Parameters

    Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Technical Parameters Common data DC Input Voltage 7…25V (wide range power supply) Ambient Temperature 0..40°C; Humidity < 95% non-condensing Dimensions in mm Size (HxWxD) 20x56x62 mm Mass 0.016 kg...

  • Page 6: Mechanical Drawing

    Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Mechanical Drawing LED 1 LED 2 LED 3 Mounting holes 3.2mm for M3 heating cooling Power On green yellow Temp Setpoint Current Setpoint Ccw → decrease Cw →...

  • Page 7: Pin & Jumper Description

    Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Pin 1 Connector Jumper Pin & jumper description The jumper J1 select the signal source for the laser current setpiont. Made in Germany by 7-11...
  • Page 8 Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Current Setpiont via external Current Setpiont via on board signal source at X2 potentiometer 0..2V = 0..2A Connector X2 type Fischer WSL6 (PIN 1 MARKED)

  • Page 9: Laser Diode Connection

    Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Laser Diode connection PIN 1 PIN 7 PIN 8 PIN 14 FUNCTION SPECIFICATION AND REMARKS Maximum ±2A NTC + Thermistor NTC 10k High potential 5V...

  • Page 10: Getting Started

    Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Getting Started Hardware Setup  Mount the driver at an appropriate heat sink. Use a heat conducting foil for interface between driver and heat sink. We strongly recommend using plastic washers for the screws when you mount the device on a heat sink with protective earth connection.

  • Page 11: Laser Diode Protection

    Sold & supported by CW Laser Diode Driver for Butterfly 14Pin Package SmartPower XS 10-2 Laser diode protection The Driver Board has a fast protection Diode on the Laser Diode Anode (+) and Cathode (-). The Ground (GND) of the Board is common with the Laser Diode Cathode. Please note that if you use systems with protective Earth.

Table of Contents