Advertisement
Time Adjustment:
Time 1 (for ↑) with 7 steps adjustable:
(Pulse)-30s-1m-5m-15m-30m-Test
Time 2 (terminals C1, C2) with 7 steps adjustable:10s-1m-5m-10m-20m-30m-60m
Note: The detector LED indicator will blink 3 �mes when the poten�ometer is adjusted and the
desired step is successfully selected.
5m
1m
30s
TIME 1
Lux Adjustment:
With 7 steps adjustable (for Load 1 only): 10-100-500-1000-2000 lux-Daylight( )-Teach In( )
* Load 2 is independent and not controlled by Lux se�ng.
Note: The detector LED indicator will blink 3 �mes when the poten�ometer is adjusted and the
desired step is successfully selected.
Pulse Func�on
For staircase �mer switch opera�on (see FIG. 2); for each detec�on the load will switch on for
1 sec and off for 9 sec as a complete cycle before next detec�on.
Test Func�on
Under Test mode the load will switch on for 3 sec for each detec�on, and switch off for 2 sec
before next detec�on. Under Test mode the Lux se�ng is deac�vated.
Presence Func�on
During the delay �me a�er the sensor was triggered, the Presence func�on will force the sensor
to switch off the load when the ambient brightness is higher than the Lux se�ng value for 5 min,
regardless of any movement detected.
Teach In Func�on
Switch the Lux se�ng to Teach-in mode at the desired ambient brightness level. The load will
turn OFF. The sensor LED indicator will flash for 20 sec while sensor learning the ambient
brightness. The sensor LED indicator and the load will stay ON for 3 sec and then go OFF, then
the learning process is done. The learned brightness value is accepted as the new brightness
switching value.
When the ambient lightness is lower than 5 lux, the sensor will accept 5 lux as the brightness
switching value. When the ambient brightness is higher than 2000 lux, the sensor will accept
2000 lux as the brightness switching value.
Push-bu�on Func�on (Op�onal)
An op�onal N.O. momentary external push bu�on can be wired to the sensor. Short press the
bu�on once to turn on the load, delay �me according to TIME se�ng; short press it again to
turn it off, delay �me (for OFF) according to TIME se�ng. Please note when using the push
bu�on feature the LUX level is disregarded.
10m
15m
5m
20m
30m
1m
30m
Test
10s
60m
TIME 2
1000
2000
500
100
10
LUX
3
INSTALLATION AND WIRING
● Please disconnect power completely and read the en�re instruc�on manual
carefully before installa�on and retain for future reference.
● Installa�on and assembly of electrical equipment must be carried out by qualified
electricians. Contact a qualified electrician in the event of fault or break down.
● A circuit breaker (250VAC, 10A) type C according to EN60898-1 of load 1 (↑)
must be installed in the fixed wiring for protec�on.
A circuit breaker (250VAC, 6A) type C according to EN60898-1 of load 2 (C1,C2)
must be installed in the fixed wiring for protec�on.
Wiring
● Normal wiring connec�on.
Load
Power Supply
C2 C1
L N N
P/S
Push
Load
Bu�on
L
N
FIG.1
● Mul�ple sensor wiring in parallel (max. 6 pcs)
C2 C1
L N N
P/S
Push
Bu�on
L
N
● For staircase �mer switch opera�on.
Staircase �mer
C2 C1
IN
L N N
P/S
N
Push
Bu�on
L
N
FIG.2
C2 C1
L N N
P/S
Push
Load
Bu�on
4
OUT
Load
μ
L
FIG.3
Advertisement
