Advertisement
4. Mounting anD asseMblY
Warning! ensure the hose is disconnected from the air supply. Do not position the hose in direct sunlight or in areas of extreme
‰
heat or cold.
4.1.
to wall mount the reel first remove the wall mounting bracket from the reel by releasing and withdrawing the two bracket pivots.
(refer to item 11 on the parts diagram. to release the pivots remove the casing screws which pass directly
through each pivot. (the pivots are each retained by two screws.)
Warning! Do not remove any other casing screws.
‰
4.2. .
fix the bracket in an appropriate position ensuring that the wall and the mounting screws and plugs will adequately support the weight
of the reel and the tension of the hose as it is pulled from the reel.
4.3.
reattach the reel to the bracket ensuring the pivots are correctly inserted and retained by the casing screws.
4.4.
ensure that the hose can be pulled out to, and reeled back from, work sites without rubbing the sides of the cable entry.
5. operation
5.1.
extending the hose.
As the hose is pulled out from the reel the action of the ratchet mechanism can be heard alternating between the usual clicking sound
and a short period of silence. if the tension on the hose is released whilst the ratchet is clicking the hose will remain extended. if the
tension on the hose is released during silent operation the hose will retract. to stop the hose retracting pull it out again a little until you
hear the ratchet clicking.
5.2.
retracting the hose.
to release the hose and allow it to automatically rewind, pull the hose out from the locked position until the clicking stops and then
release the tension on the hose. Do not let go of the hose but keep hold of it and guide the end back to the reel.
Warning! the reel tension is factory set, if any adjustment is required contact an authorised service agent. Do not remove any of
‰
the black spring cover screws.
6. Maintenance
Warning! Before attempting maintenance or inspection vent any pressure remaining in the hose.
‰
6.1.
to ensure reliable operation, clean the hose and casing regularly. Do not spray or wet the product, but clean with a cloth and
warm water. Do not use solvents or detergents, as these may cause permanent damage.
6.2.
the hose reel does not require special maintenance as it is lubricated for life. if the product needs to be opened, consult your
nearest authorised service agent.
Warning: Do not attempt to loosen, or remove, any casing screws.
‰
6.3.
replacement of the supply hose should be carried out by skilled personnel only. consult your nearest authorised service agent.
6.4.
storage.
should you wish to store the air hose, ensure it is clean and dry. Place the item in a dark, safe, dry, childproof location, where the
temperature will remain reasonably stable. Do not store in a nylon, or plastic, bag as this will encourage condensation.
recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMportant: no liability is accepted for incorrect use of this product.
WarrantY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
environmental protection
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
01284 757500
01284 703534
sA894.V3, sA895.V3 | issue 2(l) 22/12/16
www.sealey.co.uk
Web
sales@sealey.co.uk
Advertisement
