Standard Equipment; Telescope Assembly; Set-Up Tripod, Mount And Accessory Tray; Attach Telescope And Finderscope - Bushnell Deep Space 78-9514 User Manual

STANDARD EQUIPMENT

Complete Main Telescope Assembly
Altazimuth Yoke Mount
Variable Height-Hardwood Tripod
4mm, 12mm, 20mm focal length - Eyepieces.
5 x 24mm Finderscope w/ focus adjustment
Vertical Stabilizer Bar
Accessory Tray
Diagonal Mirror
3x Barlow, Erecting Lens
Hardware Pack
Tripod leg: 3-2_"bolts, 6-
Accessory tray: 3-_" bolts, 6-_" washers and 3-wingnuts
Tripod Leg Lock Screws: 3 pc.
Stabilizer Bar: 1 Mounting Screw

TELESCOPE ASSEMBLY

1. Remove all components from the carton and identify all components. READ THROUGH ASSEMBLY
INSTRUCTION BEFORE YOU ASSEMBLE YOUR TELESCOPE

2. Set-Up Tripod, Mount and Accessory Tray

Select one
Tripod Leg (5)
included in the hardware pack, insert the
the lower brackets on the
so that the middle section is securely in place. Repeat on
Screws
remaining two legs.
Locate the
Altazimuth Yoke Mount (3). Note: Before assembling tripod
legs to Altazimuth Yoke Mount, make sure the Accessory Tray Braces(7)
Locate the long bolts and washers from the hardware
face inward.
pack (
3-2_"bolts, 6-
Tripod Leg (5)
with the holes in the mount. Insert the bolts through the holes at the
top of a
Tripod Leg.
sides of the
tighten it all the way. Repeat on the remaining two
you have attached all
wing nuts.
Locate the
Accessory Tray (8).
washers and 3 - wingnuts)
and attach wingnut. Wingnuts should be positioned beneath the
Leg
wingnuts until all

Attach Telescope and Finderscope

3.
Locate
Telescope Main Tube (20).
Stabilizer Bar
Altazimuth Yoke Mount
telescope between yoke. Carefully replace the
Objective Lens (1).
Stabilizer Bar Mounting Screw
Locate the
Finderscope (17)
near the back of the
exposed screws. Replace the nuts, and securely tighten the
11
washers and 3-wingnuts
/16
and extend the
Tripod Leg.
11 washers and 3-wingnuts)
/16
as shown and align the holes in the
(fig. 1).
A washer should be positioned on both outer
Attach a wing nut to the bolt but do not
Tripod Leg.
Tripod Legs
Using the accessory tray bolts, wingnuts and washers
connect the
Accessory Tray
Accessory Tray Braces
Now, locate the
into the slot at the base of the
by removing
Locate the
Stabilizer Bar Mounting Screw (2)
into the slot to secure the
with pre-assembled
Telescope Main Tube (20)
Tripod Leg Middle Section (6).
Tripod Leg Lock Screw
Tighten the
Tripod Leg Lock
. Position the mount over the
Tripod Legs
to the mount, securely tighten all
to the
Accessory Tray Braces (7).
are attached as some adjustments may be required.
Vertical Stabilizer Bar (10)
Altazimuth Yoke Mount (3)
Altitude Lock Knobs (19).
Altitude Lock Knobs
Finderscope Mount (15).
and place the
Using
Tripod Leg Lock Screws (9)
into
Tripod Leg
. Once
Accessory Tray.
. Then, secure telescope to
from telescope and positioning the
and remove lens cover from
in the hardware pack. Insert the
Vertical Stabilizer Bar
Remove the two nuts located
and
Finderscope Mount
Finderscope Mount
fig. 1
( 3-_" bolts, 6-_
Start with one
Tripod
Do not tighten
and insert the
Vertical
60mm
in place.
assembly over the
in place.