Advertisement
2. INTRODUCTION
Heavy-duty axle stands to safely support vehicles for extended periods of time. Large crutch for even load distribution. Heavy gauge steel frame
and base plate with welded construction gives superior strength and safety. Supplied with captive, multi-position pin load support. Sold in pairs.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AS20
Capacity Each: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 tonnes (20,000 kg)
Capacity Pair: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 tonnes (40,000 kg)
Minimum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335mm
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490mm
4. OPERATION
4.1.
Refer to vehicle handbook for correct jacking procedure. Check to ensure manufacturer's recommended jacking points are in good
condition.
4.2.
Position stands beneath recommended support points.
4.3.
To adjust stands, lift column up to jacking point, lower until a pin hole is visible, push pin all the way through.
4.4.
Carefully and slowly lower vehicle onto stands. Ensure load bearing points sit in the centre of the yoke/saddle and that the stands are
stable. Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle onto the stands.
▲
DANGER! You must follow instructions carefully and ensure you DO NOT load the stands off centre.
Failure to heed these warnings may cause damage, injury or loss of life.
5. MAINTENANCE
5.1.
Before each use, check that the stands welds and component parts are not flawed and that there are no missing parts.
Any suspect axle stands must be removed from service immediately.
5.2.
Owing to the potential hazards associated with stands, do not misuse, or make any modification, to the stands or components.
5.3.
It is the responsibility of the owner to ensure that the operator has read these instructions together with the safety features on the
side of the stand and that the operator is familiar with the stand's use and limitations.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal of it according to local regulation
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Environmental Protection
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
s.
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
AS20
Issue: 1 - 28/04/17
Advertisement
