Advertisement
Available languages
Available languages
ABI-EV2000S00
ABI-EV2008S00
ABI-EV2014S00
TV-over-Twisted-Pair
RF amplifier
Quick Start Guide
1
Package Contents
•
DIN rail mountable RF Amplifier modules
•
Quick Start Guide
•
3 RJ45 Termination plugs
2
Tools
•
Spanner 11mm
3
Introduction
The ABI-EV2000S00 and ABI-EV2008S00 are RF amplifiers with
integrated return path. The modules are equipped with one coaxial
input for CATV signal or DVB-T antenna. The modules have one
coaxial TV input and 4 independent RJ45 (Twisted Pair) outputs on
the front.
The ABI-EV2008S00 has 2 coaxial extension outputs to feed one
or two ABI-EV2014S00 modules, bringing the capacity to 8 or 12
TV sets.
A range of Twisted Pair to Coax adapters (with or without
adjustment, filters, IR...) is available for installation at the receiver
end (i.e. ABI-AC1001S00, ABI-AC1002S00,...).
All 4 ports of the modules are ready for Docsis compliant in-band
return path providing interactive digital TV services (e.g. VOO,
UPC,...)
4
Connectors
RF amplifier - 4port
RF IN 1
English
140507_ABI-EV20XX_QSG_ML_RevA.docx
Seulement ABI-EV2008S00
TV-over-Twisted-Pair
PS IN
- Master
+5VDC
RF OUT2
RF OUT3
ABI-AC1001S00
ABI-AC1002S00
ABI-AC1010S00
5
Power
Load ratio for ABI-EV2000S00 and ABI-EV2008S00 = 0,6A.
Load ratio for ABI-EV2014S00 = 0,0A.
Maximum allowed load ratio (sum of the load ratios for all modules) for
power supply ABI-PS1001S14 = 4A.
6
Installation
Power Off the central ABI-PS1001S14 Power Supply by means of the
Circuit Breaker installed in the 'Comm Center Cabinet', or by removing
the mains power cord from the Power Supply.
1.
Make sure the shielding of the Network Interface Unit (NIU) or
CATV transition point is properly connected to the protective
ground.
2.
Open the 'Comm Center Cabinet'
3.
Click the ABI-EV20XXS00 unit on the metal DIN-rail.
4.
The ABI-EV20XXS00 is supplied with a grounding wire,
connected to the input F-connector.
This wire (1) must be connected to the protective ground of
the installation.
The following system devices also need to be connected to
the protective ground: The DIN-Rail frame (2) and the Power
supply (3)
5.
Connect one of the unused POWER connectors of the ABI-
PS1001S14 Quadruple Power Supply (5VDC - 4A).
6.
Connect a coax cable from the CATV connection point (NIU)
or the CATV transition point to the coax input connector
CATV/ANTENNE on the top of the unit.
7.
If needed, connect extension modules (ABI-EV2014S00) to
the coaxial CATV/ANTENNE outputs using a coaxial patch
cord.
TV-over-Twisted-Pair
RF amplifier - 4 port
RF IN 1
Page 5
ENGLISH
T V-o ver-Twis ted- Pair
PS IN
RF amplifier - 4po r t
- Master
+5VDC
RF IN 1
RF OUT 2
RF OUT 3
1
2
PS1001
3
4
PS IN
TV-over-Twisted-Pair
Slave - In-band RP
- Master
+5VDC
RF OUT2
RF OUT3
PE1002
TV-over-Twisted-Pair
Slave - In-band RP
abitana
N.V.
S.A.
Advertisement
