Advertisement
Quick Links
WARNING
・Confirm compatibility of Grinder and Blade before use.
・Read the instruction manual for the TORNADO, the Grinder, and the Blade before use.
・Be sure to wear protective goggles, dust mask, protective footwear, earplugs and other protective equipment when working.
・Ensure the TORNADO is securely mounted onto the Grinder.
・Confirm the Blade does not rub on the inside of the TORNADO.
・Keep TORNADO away from gasoline, thinners, petroleum and paraffin.
・Do not use TORNADO when it is damaged, cracked or bent as this could lead to injury.
・Do not use worn-out Blade.
SPECIFICATIONS
Model Code
NK-125
Suitable Blade type
D125 x iD20/22 x T1.5-2.2 Diamond Blades.
Soft concrete, Block, Stone, ...etc.
Cutting Material
Cutting Depth
Weight (main unit)
520g
BOSCH
Attachable
MAKITA
Grinders
HITACHI
RYOBI
INSTALLATION OF GRINDER
(1) Change the SW position of the Grinder.
③
Guard
SW
①
Screw
②
④
(2) Fit the Grinder by tightening the screws of the Connecter. (Hold the top surface of [a] Main Unit)
Hold
Grinder
[d]
②
[c]
NK-125 / NK-125A
INSTRUCTION MANUAL
NK-125A
5-33mm
620g
: GWS5/6/7/8 100mm series
: 9553/9556/9563H series
: G10 series, PDA-100M
: 100mm series
①Take the Guard off.
②Remove the Screws.
③Turn the Grinder Body to locate the SW upper position.
④Tighten the Screws.
Grinder
Be sure to turn off the grinder and remove the plug
from the power supply before installation.
[a]
HITACHI Grinder
[i]
Change the Connecter by
[i] Wrench.
①Remove preset
[c] M-Connecter.
①
②Set [d] H-Connecter.
OVERVIEW
[a] (NK-125A)
[a] Main Unit / [b] Dust Bag / [c] M-Connecter / [d] H-Connecter
[e] Setscrews / [f] Flange(Silver) / [g] Flange(Black)
[h] Washer / [i] Wrench
WARNING
Confirm NO tilt.
O K
Adjust the angle
of Grinder to
O K
make the bottom
surface flat.
[e]
[a]
[b]
[d]
[c]
[e]
[a] (NK-125)
N G
N G
BOSCH Grinder
Tighten [e] Setscrew after
fitting the Grinder into [a]
Main Unit by [i] Wrench.
Do NOT over tighten [e] Set
Screws or they could cause
damage or deformation to the
Grinder and Connecter.
[i]
[f]
[g]
[h]
[ i ]
Advertisement
Related Manuals for NAKAYA Tornado NK-125
Summary of Contents for NAKAYA Tornado NK-125
- Page 1 NK-125 / NK-125A INSTRUCTION MANUAL WARNING ・Confirm compatibility of Grinder and Blade before use. ・Read the instruction manual for the TORNADO, the Grinder, and the Blade before use. ・Be sure to wear protective goggles, dust mask, protective footwear, earplugs and other protective equipment when working. ・Ensure the TORNADO is securely mounted onto the Grinder.
- Page 2 INSTALLATION OF BLADE 1. Loosen Knob Bolt and open [a] Main Unit. 2. (MAKITA Grinders and BOSCH GWS7-100 ONLY) Wheel Nut direction. Set [h] Washer into the Spindle. 3. Set proper Flange [f] or [g] into the Spindle. 4. Set the Blade on the Flange. Blade 5.