GV BD06 User Manual

THERMOSTAT BD06
SEMI-PROGRAMMABLE DIGITAL - WHITE
USER MANUAL
I - INTRODUCTION
Dear User:
Congratulations on chhosing a
manual before installing/using the thermostat.
This thermostat is used to control the temperature of heating cables or
heating mats for electric under oor heating in a given room, wether in a
domestic, commercial or industrial environment.
While we try to provide the best device possible, we are always available for
technical support. If you have any questions, please contact us.
II - TECHNICAL PARAMETERS AND MAIN CHARACTERISTICS
Technical parameters
Voltage
Amperage
Working environment
Consumption
Protection index
Programmable temperature
Temperature control precision
Main characteristics
Programs
Probe reading options
External dimensions
Material
Screen background color
Memory in case of electrical failure
Child lock
Installation
III - CAUTIONS FOR INSTALLATION
ATTENTION!
When being installed, this thermostat may cause an
electric shock. Make sure the installation is done by
a quali ed electrician.
1. Installation should only be done when the electric supply is o , otherwise it can
damage the thermostat and cause an electric shock.
2. Choose the most suitable location for installing the thermostat (about 1,60m
above the oor). It must not be installed at eye level.
3. Installation should not be made at altitudes higher then 2000m above sea level.
IV - INSTALLATION
1. Separate the thermostat from the display using a screwdriver to press the
groove at the back of the thermostat and pushing the display upwards ( g.1).
2. Follow the wiring diagram ( g. 2) to connect the power, the heating cable
and the oor probe.
3. Use the two screws provided to x the outer ring and the thermostat base
to the electrician's deep box previously installed ( g. 3) and make sure that it
is properly installed.
4. Attach the display to the four projections on the mounting plate and push it
downwards (never press the LCD display directly). The installation is complete.
Turn on the power to test the thermostat.
thermostat. Please refer to this user
AC 230V, 50-60Hz
16 A
0ºC ~70ºC
<0.3 W
IP20
5ºC ~ 35ºC
0.5 ºC
3 daily, cyclic active scheduling
3 (internal, external and both)
86mm x 86mm x 27mm
PC + ABS
Blue
Time and schedules
Yes
Wall-Inserted Type
Fig. 1 - Thermostat opening
Fig. 2 - Wiring diagram
Fig. 3 - Thermostat Installation
V - THERMOSTAT INTERFACE
Vacation Mode
Anti-freeze mode
Manual mode
AUTO
Automatic mode
Room temperature
SET
F C
Set temperature
Advanced Options symbol
Days of the week
Programming Symbol
PROG
0
Funções dos botões
Switch on / o thermostat.
Press for 3s to activate / deactivate child lock
Rotate clock wise Increases the Value, Rotate in the opposite direction
Decreases Value
Fast Press Con rms the option (Enter key)
Pressing for 3s, when released, enters settings mode
VI - THERMOSTAT PROGRAMMING
»
ON / OFF
Press the button to turn on the thermostat (located on the right side of the
thermostat).
Press the button again to turn o the thermostat and cut the power to the
heating cable or network.
»
SETTING THE TIME AND DAY OF THE WEEK
With the thermostat on, press the button
enter the settings mode.
Turn the knob until the symbol
to enter the Hour and day of the week settings.
Rotate the knob to set the minutes and con rm with a short press on the
same button, after the minutes the hours follow with the same procedure.
After setting the hours and pressing the button
the week ash (
and 7 represents Sunday. After setting the day of the week, press the button
again to exit the menu and wait 5 seconds to exit the settings mode.
IP 20
AC230V 50/60Hz
current imax:16A
Load
L1 N1 N L
5
1 2 3 4
6
Heating Cable / Mat
16A
N (Neutral Wire)
L (Live wire)
AC220V, 50~60Hz
Floor Sensor
Child lock
Programs 1 2 and 3
P P P
1 2 3
Energy Saver Mode
ROOM
Heating
F C
Confort Mode
NTC
TIME
Hours
6 12 18 24
and release after 3 seconds to
TIME
ashes and short press the button
, you will see the days of
). 1 represents Monday, 6 represents Saturday
24 hours of the day