Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Inspire SLEEP REMOTE
Summary of Contents for Inspire SLEEP REMOTE
- Page 1 INSPIRE SLEEP REMOTE Inspire Sleep Remote Model 2500 Rx Only...
- Page 2 The following is a registered trademark of Inspire Medical Systems, Inc.: Inspire ® The following is a trademark of Inspire Medical Systems, Inc.: Inspire Sleep Remote...
- Page 3 Turn therapy off Decrease stimulation strength Increase stimulation strength Replace sleep remote batteries If the light is on but not flashing, your generator battery may be If the light is on and flashing, communication with your generator has been interrupted...
- Page 4 IP22 and moderate amounts of dripping water Note: The sleep remote meets the water ingress rating of IP22, maintaining safe operation. Exposure to water or liquids could result in a loss of performance. Keep the sleep remote dry. Refer to “Battery and Sleep Remote Disposal”...
-
Page 5: Inspire Sleep Remote
Status ring Pause Increase Decrease (stimulation strength) (stimulation strength) Therapy Off Figure 1. Sleep remote front view Status Ring White Therapy is off Green – Solid Therapy is on and stimulation is on Green – Dimming and Therapy is on, stimulation is paused... - Page 6 Pausing Therapy • While therapy is on, press the Therapy On button ( and hold the sleep remote over your generator for 10 seconds or until the sleep remote produces an audio tone. iv English...
- Page 7 Sleep remote Generator battery light light Figure 2. Sleep remote back view Status Indicators Replace sleep remote batteries If the light is on and not flashing, your generator battery may be low, call your doctor If the light is on and flashing, communication with your generator has been interrupted.
- Page 8 • If the sleep remote produces three rapid beeps, you have not found the generator location. Try again. Audio Tones Two beeps with the •...
-
Page 9: Table Of Contents
3. Safety Information 7 Warnings 7 Precautions 8 System and Therapy 8 Patient Activities 9 Interference 9 4. Using Your Sleep Remote 11 Sleep Remote Buttons 12 Status Ring 13 Stimulation Strength Gauge 14 Status Lights 16 Audio Tones 18... - Page 10 5. Living with Your Inspire System 33 Travel Information 33 When to Call Your Doctor 33 Manufacturer's Information 34 6. Maintaining Your Inspire Sleep Remote 35 Sleep Remote Batteries 35 Checking the Sleep Remote Battery Status 36 Replacing the Sleep Remote Batteries 37...
- Page 11 Inspire Medical Systems Limited Warranty 53 Inspire Sleep Remote English ix...
-
Page 13: Glossary
Lead — A thin, implanted wire with protective coating that connects to the generator. The Inspire system has a respiratory sensing lead and a stimulation lead. Pause — A delay in therapy that allows the patient to temporarily stop stimulation without turning the therapy off. - Page 14 Sleep Remote — Device the patient uses to turn therapy on and off, and to change stimulation strength within limits set by a doctor. Start Delay — A delay between when the therapy is turned on and when the stimulation begins. Start Delay allows the patient to fall asleep before stimulation begins.
-
Page 15: Introduction
® Upper Airway Stimulation (UAS) therapy (Figure 3a). Your doctor has given you an Inspire Sleep Remote (Figure 3b). Use your sleep remote to turn your therapy on and off and adjust the strength of stimulation. Implanted components Inspire Sleep Remote Figure 3. -
Page 16: About This Manual
About This Manual This manual provides information on using and maintaining your Inspire Sleep Remote. The sleep remote should only be used according to the instructions in this manual and the instructions provided by your doctor. This manual also contains information about Inspire therapy. -
Page 17: Inspire Therapy
2. Inspire Therapy You have received an Inspire system to deliver Inspire Upper Airway Stimulation (UAS) therapy. Your doctor prescribed UAS therapy to treat your sleep apnea. For more information about your Inspire system, refer to your Inspire Patient Manual. -
Page 18: Therapy Summary
When you are preparing to go to sleep, you will use your sleep remote to turn your therapy on. You will feel a brief stimulation confirming that therapy has been turned on. After the confirmation, stimulation is delayed so you have time to fall asleep. -
Page 19: Additional Therapy Information
When the delay time has passed, the Inspire system delivers mild stimulation to the nerve that controls your tongue movement (the hypoglossal nerve) as it senses breathing. The stimulation causes the upper airway muscles to stiffen, preventing airway blockages. The therapy does not wait for an apnea to occur before delivering stimulation. -
Page 21: Safety Information
Inspire Medical Systems Inc. to request a replacement. Warnings Choking hazard. The sleep remote batteries may pose a choking hazard. Keep the sleep remote and batteries away from children and pets. Flammable environment. Avoid using the sleep remote in the presence of flammable gases and/or fumes. -
Page 22: Precautions
Sleep remote connection to other equipment. Do not connect the sleep remote to other equipment, cables, or devices. The sleep remote is only for use with the Inspire system. Connection to other equipment could damage the sleep remote. -
Page 23: Patient Activities
1. Move away from the equipment or object. 2. If possible, turn off the equipment or object. 3. Use the sleep remote to turn your therapy off. 4. If the above actions do not resolve the effects of the interference, or you suspect that your therapy is not the same after exposure to interference, contact your doctor. -
Page 25: Using Your Sleep Remote
4. Using Your Sleep Remote Your sleep remote allows you to turn your therapy on before you go to sleep, off during waking hours, and pause therapy if you wake and need time to fall back to sleep. It also allows you to adjust the stimulation strength within a range determined by your doctor. -
Page 26: Sleep Remote Buttons
(stimulation strength) Therapy Off Figure 6. Sleep remote buttons The sleep remote buttons (Figure 6) allow you to turn your therapy on and off, and to pause therapy. Also, you can increase or decrease your stimulation strength within a range selected by your doctor. -
Page 27: Status Ring
). The status ring lights up and indicates if therapy is on, off, or paused. To check your therapy status: • Pick up or gently shake the sleep remote. The status ring lights up to indicate your therapy status. Status ring light:... -
Page 28: Stimulation Strength Gauge
Note: If your doctor did not program a range of stimulation strengths for you to use, the Increase ( ) and Decrease ) buttons do not change your stimulation strength. Upper limit light Stimulation strength gauge Figure 8. Stimulation strength gauge 14 English Inspire Sleep Remote... - Page 29 To check your stimulation strength: • Pick up or gently shake the sleep remote. The stimulation strength gauge indicates your current stimulation strength. Note: Your sleep remote may not respond to a gentle shake if it has been excessively bounced during the previous 30 minutes, such as when it has been in a car.
-
Page 30: Status Lights
Figure 9. Status lights The generator light and the sleep remote battery light on the back of your sleep remote indicate the status of your generator and sleep remote batteries (Figure 9). Note: When either status light turns on, yellow bars on the status ring flash. - Page 31 Status light: Means: Both status lights off Sleep remote and generator are operating normally Sleep remote Sleep remote batteries are low and need battery light on to be changed Generator light on Contact your doctor Both status lights Replace sleep remote batteries, because low batteries may be preventing normal sleep remote operation.
-
Page 32: Audio Tones
Audio Tones When audio tones are turned on, the sleep remote beeps when a change to the therapy settings is successfully completed. Audio tone: Means: • Your change was successful. Two beeps with the second beep at a higher tone than the first •... -
Page 33: Turning Audio Tones On Or Off
Turning Audio Tones On or Off Your sleep remote audio tones can be turned on or off. Inspire recommends that you keep audio tones on. Turning audio tones on or off: 1. Remove the battery compartment cover. (For instructions, refer to page 37.) 2. -
Page 34: Using Your Inspire Sleep Remote
The sleep remote attempts to communicate with your generator for 10 seconds. If communication is not successful after 10 seconds the sleep remote beeps rapidly three times and the sleep remote light indicate the therapy status for several seconds. Radio signals... - Page 35 4. Slowly adjust the sleep remote position until the sleep remote produces a tone or 10 seconds pass. 5. Remove the sleep remote from your body and review the sleep remote lights to confirm that the change was communicated to your generator.
- Page 36 3. Position the sleep remote directly over your generator and against your body. The buttons should face away from your body (Figure 12). 4. Adjust the sleep remote position until the rear surface of the remote, opposite the Therapy On button ( ), is directly over your generator (Figure 5).
-
Page 37: Communicating With Your Generator
Communicating with your Generator When the sleep remote is communicating with your generator, the status ring and stimulation strength gauge blink on and off. The blinking lights indicate the change the sleep remote is attempting to make to your generator. Status ring Figure 13. - Page 38 Whole gauge blinking Turning therapy off white Whole gauge blinking Turning therapy on or pausing therapy green One step on the gauge is Increasing or decreasing stimulation blinking strength. The newly selected stimulation strength step is blinking. 24 English Inspire Sleep Remote...
-
Page 39: Turning Therapy On
(Figure 15). Figure 15. Correct positioning of sleep remote over generator 3. Wait until the sleep remote produces a tone or 10 seconds pass. 4. Check the status ring. -
Page 40: Turning Therapy Off
– If the sleep remote lights are off, gently shake the remote and the lights turn on. Note: When you turn stimulation on, the generator will produce a brief stimulation pulse, and then your generator will delay further stimulation while you fall asleep. -
Page 41: Pausing Therapy
2. Position the sleep remote directly over your generator and against your body with the buttons facing away from your body (Figure 15). 3. Wait until the sleep remote produces a tone or 10 seconds pass. 4. Check the status ring. -
Page 42: Increasing Stimulation Strength
1. Turn therapy off by pressing the Therapy Off button ( and positioning the sleep remote over your generator. 2. Wait until the sleep remote produces a tone or 10 seconds pass. 3. Turn therapy on by pressing the Therapy On button ( and positioning the sleep remote over your generator. -
Page 43: Decreasing Stimulation Strength
2. Position the sleep remote directly over your generator and against your body with the buttons facing away from your body (Figure 15). 3. Wait until the sleep remote produces a tone or 10 seconds pass. 4. To test the new stimulation strength: a.Turn therapy off. - Page 44 1. Turn therapy off by pressing the Therapy Off button ( and positioning the sleep remote over your generator. 2. Wait until the sleep remote produces a tone or 10 seconds pass. 3. Turn therapy on by pressing the Therapy On button ( and positioning the sleep remote over your generator.
- Page 45 You will receive one short stimulation immediately when therapy is turned on. Inspire Sleep Remote English 31...
-
Page 47: Living With Your Inspire System
5. Living with Your Inspire System Travel Information As you travel, your sleep remote will allow you to operate your generator at any travel destination while you sleep. It is possible that airport security devices may affect the operation of your generator and detect the metal in your generator. -
Page 48: Manufacturer's Information
This could result from movement of the stimulation lead. • The generator light on the back of your sleep remote is If you are unable to reach your doctor immediately, try again at a later time. Meanwhile, discontinue therapy and contact the doctor who implanted your system. -
Page 49: Maintaining Your Inspire Sleep Remote
6. Maintaining Your Inspire Sleep Remote You will need to replace your sleep remote batteries and clean the sleep remote as needed. Although your doctor will monitor your generator battery status during your follow-up appointments, you can also use your sleep remote to check your generator battery status. -
Page 50: Checking The Sleep Remote Battery Status
• Do not leave batteries in the sleep remote if it will not be used for more than 4 weeks. Batteries left in the sleep remote may corrode and damage the sleep remote. Checking the Sleep Remote Battery Status Develop a routine where you check your sleep remote battery status regularly. -
Page 51: Replacing The Sleep Remote Batteries
Replacing the Sleep Remote Batteries The sleep remote batteries are located in a battery compartment on the bottom of the sleep remote. To remove the battery compartment cover: 1. Hold the sleep remote with the battery compartment cover facing upwards as shown in Figure 16. - Page 52 To replace the sleep remote batteries: 1. Insert your finger in the finger hole to loosen the first battery, and then gently remove the batteries. 2. Position each battery to match the figure in the battery compartment (Figure 17). Do not connect...
-
Page 53: Battery And Sleep Remote Disposal
Inspire for disposal. Cleaning Your Sleep Remote Clean the outside of the sleep remote with a slightly damp cloth. The sleep remote is not sterile and is not intended to be sterilized. Diluted mild household detergents will not damage the sleep remote. -
Page 54: Handling Your Sleep Remote
Handle your sleep remote with care. Mishandling the sleep remote can damage the sleep remote. • Do not drop the sleep remote. Protect the sleep remote against sharp blows and physical shocks. • Do not disassemble or tamper with the internal components of the sleep remote. -
Page 55: Checking The Generator Battery Status
To check the generator battery status: 1. Pick up or gently shake the sleep remote. 2. Check the generator light ( ) on the back of your sleep remote. If the light is on, contact your doctor. -
Page 57: Troubleshooting Your Sleep Remote
7. Troubleshooting Your Sleep Remote The following table provides possible solutions to common questions that may arise when using your sleep remote. If you need further assistance in setting up, using, or maintaining your sleep remote, or to report problems with your sleep remote, contact your doctor or Inspire Medical Systems, Inc. - Page 58 • If the problem persists, call compartment. your doctor. Both status lights • The sleep • Replace the sleep remote on the remote batteries batteries with new batteries. back of the sleep may be very low Make sure that you are not...
- Page 59 You do not hear • Audio tones are • Turn audio tones on (refer to audio tones, but turned off. page 19). the sleep remote is working. You hear three • The stimulation • Confirm that the current beeps after...
- Page 60 Stimulation is not • Increase stimulation (refer to strong enough. page 28). You feel that a • The sleep • Hold the sleep remote closer change took remote was too to your generator. Review the place after you far from the...
- Page 61 • Your generator • Pick up or gently shake the may need sleep remote. If the generator attention from status light ( ) on the back of your doctor. the sleep remote is on, contact your doctor. Inspire Sleep Remote English 47...
- Page 62 1. Immediately remove the Your sleep sleep remote from the water. remote falls into water. 2. Dry the sleep remote with a towel. 3. Remove the batteries and dry the battery compartment if needed. 4. Allow the battery...
-
Page 63: Specifications
8. Specifications If the sleep remote may have been stored at high or low temperatures or at greater than 90% humidity, store the sleep remote at room temperature and at less than 90% humidity for one hour before use. This will allow the remote to return to normal operating temperature. -
Page 64: Connections To Additional Equipment
Local laws take priority over the requirements of this section. Contact your doctor or Inspire for additional information. Do Not Modify Do not modify the sleep remote. Changes or modifications could void the user's authority to operate the equipment. FCC Statements This device complies with part 15 of the FCC Rules. - Page 65 • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Inspire Sleep Remote English 51...
- Page 67 EXCLUDED from any transaction and shall not apply. Inspire Medical Systems will not be liable for any damages, whether direct, consequential, or incidental caused by tool defects, failures, or malfunctions, whether such claims are based on warranty, contract, tort or otherwise.
- Page 68 This is considered normal for those patients and not a malfunction or defect in the IPG. If the purchaser complies with the Terms and Conditions, Inspire Medical Systems will issue a limited warranty toward the purchase of a new Inspire Medical Systems IPG product.
- Page 69 The applicable limited warranty period for each product is listed and calculated as follows: 1. Three (3) years from date an IPG or lead is implanted in the patient. 2. One (1) year from the date a physician or Inspire Sleep Remote is first used. Inspire Sleep Remote...
- Page 72 5500 Wayzata Blvd, Suite 1600 Golden Valley, MN 55416 Tel. 1-844-672-4357 Toll Free or 763-205-7970 Fax 763-537-4310 www.inspiresleep.com MedPass SAS 95bis Boulevard Pereire 75017 Paris – France +33 (0)1 42 12 28 84 © Inspire Medical Systems 2020 All Rights Reserved 200-161-101 Rev E...
Need help?
Do you have a question about the SLEEP REMOTE and is the answer not in the manual?
Questions and answers
how do I open the battery compartmen
To open the battery compartment on the Inspire Sleep Remote:
1. Gently rotate the cover upwards.
2. Insert your finger in the finger hole to loosen the first battery.
3. Gently remove the batteries.
This answer is automatically generated
I lost my card and wondering how to locate my model number from my remote. I see a SLP023496N and PN200-139-001-REV C. Not sure which is the model. I have imaging coming up and they would like to know so they can tell if its safe to do imaging on my head
The model number for the Inspire Sleep Remote with part numbers SLP023496N and PN200-139-001-REV C is 2580.
This answer is automatically generated
Can I turn inspire on/off with iPhone?
The provided context does not mention using an iPhone to turn the Inspire Sleep Remote on or off. It states that if your remote does not pair with your phone via Bluetooth or if you do not track your sleep with the Inspire app, you will need to bring your remote to your doctor's appointment. However, it does not confirm whether an iPhone can be used to turn the device on or off.
This answer is automatically generated
The remote will turn on pause and stop but not activate
The Inspire Sleep Remote may not activate due to the following reasons:
1. Therapy is Off – The device may not have been turned on. Check the sleep remote’s status ring; if it is white, therapy is off. Turn therapy on again.
2. Electronic Interference – Other electronic devices may be interfering with communication between the sleep remote and the generator. Move away from other electronic devices and try again.
3. Delayed or Paused Stimulation – If the status ring is slowly dimming and brightening green, therapy is on but stimulation is paused. Stimulation will start automatically after the Start Delay or pause time.
4. Low Stimulation Strength – If the status ring is solid green but no stimulation is felt, the stimulation strength might be set too low. You may need to increase the stimulation strength.
If these steps do not resolve the issue, further troubleshooting may be needed.
This answer is automatically generated
In the battery compartment there is what appears to be a charging port. How can this be used? Can charging it take the place of batteries or charge batteries? Mine is a Model 2500 Inspire
The charging port in the battery compartment of the Inspire Model 2500 Sleep Remote should not be used to connect anything. It does not replace or charge batteries. The remote uses two AAA or LR03 alkaline batteries, which must be replaced when needed. Rechargeable batteries should not be used.
This answer is automatically generated