Table of Contents
Advertisement
Quick Links
Tsubaki
H e l i c a l P o w e r D r i v e
H D R / H D M S e r i e s
I n s t r u c t i o n M a n u a l
Thank you for purchasing this Tsubaki Helical
Power Drive reducer.
In order to fully realize the characteristics of
this reducer, please read the manual carefully
and use it for installation and inspection.
Please ensure that this manual is delivered to
the customer who will use the reducer.
Tsubaki E&M Co.
Advertisement
Table of Contents
Related Manuals for Tsubaki HDR Series
Summary of Contents for Tsubaki HDR Series
- Page 1 H D R / H D M S e r i e s I n s t r u c t i o n M a n u a l Thank you for purchasing this Tsubaki Helical Power Drive reducer.
- Page 2 Contents 0. Safety precautions ———————————————————————————————————————————————————————————————— P 2 1. When purchased —————————————————————————————————————————————————————————————————— P 2 2. Installation ——————————————————————————————————————————————————————————————————————————— P 3 (1) Ambient conditions —————————————————————————————————————————————————————————— P 3 (2) Transport ——————————————————————————————————————————————————————————————————————— P 3 (3) Mounting the motor —————————————————————————————————————————————————————————— P 3 (4) Installation ————————————————————————————————————————————————————————————————————— P 3 (5) Connection ————————————————————————————————————————————————————————————————————...
-
Page 3: Safety Precautions
・ Do not use the HDR/HDM Series when damaged. Otherwise there is a risk of injury and damage to equipment. ・ Do not remove the nameplate. ・ Alterations to the reducer by the customer are not covered by the warranty and Tsubaki E&M assumes no responsibility for them. (Upon receipt of your reducer) ・... -
Page 4: Installation
2. Installation (1) Ambient conditions Install the reducer without a motor in an ambient temperature range from -10 to 50°C and the reducer with a motor in an ambient temperature range from -10 to 40°C in a location that is well-ventilated, less dusty, and low in humidity. Do not use the reducer in locations with corrosive liquids or gases, or in flammable or explosive locations. - Page 5 CAUTION - Connecting the motor and driven machine (input shaft of the HDR Series, solid output shaft type) - ・ When connecting the HDR/HDM Series to a motor and the driven machine, pay careful attention to centering, belt tension, and the parallelism of the pulleys.
- Page 6 - The input and output shaft diameters are finished to h7. - When using a coupling or similar element to connect the input and output shaft to another shaft, align and fix it in place so that the center of the mating shaft is aligned accurately.
-
Page 7: Operation
Lubrication oil volume Size Shaft arrangement Mounting code 1 3 (3) 6 (5) 8 (7) 12 (11) 18 (15) 27 (24) 30 (27) Mounting code 2, 3 4 (4) 6 (6) 8 (8) 12 (13) 20 (18) 29 (26) 34 (31) Note) (1) Figures in ( ) for 010 to 040 indicate the oil volume for a right angle type 2-stage housing. -
Page 8: Maintenance
・ The reducer is not subject to shock or overloads. Note) Loading the reducer above the allowable capacity can shorten the life of the gears, resulting in damage to the reducer. Do not load the reducer above its allowable torque. Note) The reducer may generate heat during the first two or three days of operation. - Page 9 Attach the oil seal Before pressing the oil seal into the seal support, apply grease to the oil seal lip groove. (Approximately 50% of the lip space) Press the oil seal into the seal support. When pressing the oil seal, use a flat press fixture to press in the oil seal so that it is not slanted, as shown in the figure below.
-
Page 10: Limited Warranty
(2) We have taken all precautions regarding the content of this instruction manual so that it contains no mistakes or flaws. However, if you find a mistake or flaw, please contact Tsubaki E&M. Limited Warranty Tsubaki E&M Co.: hereinafter referred to as “Seller” Customer: hereinafter referred to as “Buyer” Goods sold or supplied by Seller to Buyer: hereinafter referred to as “Goods”... - Page 11 Tsubaki E&M Co. For inquires related to this instruction manual, please contact customer service. Customer service Tel: (0120) 251-602, Fax: (0120) 251-603 H e a d q u a r t e r s F a c t o r y Kotari Kuresumi 1-1, Nagaokakyo, Kyoto, Japan 617-0833...
- Page 12 TA34.00TS TSUBAKI REDUCER China RoHS Instruction 本资料是中国R0HS 的必备资料 （China RoHS requisite document） GMTA(GMTE)、HMTA(HMTE)､GMMT､HMMT､HDM(HDME) 有害有毒物质或者元素（ Hazardous Substances or Elements） 零部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Part Name) (PBDE) （Pb） （Hg） （Cd） （Cr(Ⅵ)） （PBB） 电动机 × ○ ○ ○ ○ ○...
Need help?
Do you have a question about the HDR Series and is the answer not in the manual?
Questions and answers