Subscribe to Our Youtube Channel
Related Manuals for Benelli Mantus MTB
Summary of Contents for Benelli Mantus MTB
- Page 1 USER MANUAL Benelli Mantus MTB This manual contains important safety, performance and service information. Read it before you take the first ride on your new bicycle and keep it for reference.
-
Page 2: Table Of Contents
Pedal ......................8 Adjust the handle bar position ................ 8 5. Check before riding ..................... 8 6. Riding a Mantus MTB ..................9 7. The display ....................... 10 850C button LCD color screen (LCD) ............10 ON/OFF operation ..................10 Pedal Assist Selection ................. -
Page 3: Preface
1. Preface 1.1 Welcome Dear Benelli owner: Thank you for your love of Benelli electric bicycles, and warmly welcome you to become a Benelli user. Before you start your journey riding with the wind, please read this user manual carefully. -
Page 4: Vehicle And Parts
3. Vehicle and parts Benelli Mantus MTB 1、Tyres 2、Rim 3、Front Hub 4、Brake Disc 5、Front Fork 6、Fork Headset 7、Power Switch 8、Frame 9、Saddle 10、Seat Post 11、Seat Post Clamp 12、Battery 13、Brake Caliper 14、Center Motor 15、Chainwheel & Crank 16、Pedal 17、Chain 18、Reflector 19、Rear derailleur 20、Cassette 21、Speed sensor 22、Handle Grip 23、Brake Lever 24、Thumb shifter 25、Handlebar 26、Displayer 27、Stem 28、Display Button BENELLI BRAVO... -
Page 5: How To Set Up The Front Wheel
Then, slide the spring and nut onto the rod, tighten the nut. Continue to tighten the nut while opening and closing the lever until a good resistance is achieved. 3. Make sure the lever is flipped up towards the frame to avoid snapping BENELLI BRAVO... -
Page 6: How To Set Up The Handlebar And Display
Then connect the blue wire on display to blue wire on bike and green wire on display to green wire on bike. Install the control button on the left side of the handlebar. BENELLI BRAVO... -
Page 7: How To Install/Remove The Battery
"click" sound. 4. The battery switch is located at the bottom, click to turn on or off the battery BENELLI BRAVO... -
Page 8: Pedal
5. Check before riding The power circuit and lighting are working. The front and rear brake lever are working. The handlebars are tightened. The front & rear wheels are tightened. BENELLI BRAVO... -
Page 9: Riding A Mantus Mtb
The tyre pressure is normal. Check the reflector for contamination before cycling. 6. Riding a Mantus MTB H H o o w w t t o o s s t t a a r r t t Press the power on/off button, the motor starts. When you sit firmly on the bike, slowly rotate the throttle, and the bike will start moving, and then slowly accelerate. -
Page 10: The Display
(AVG SPEED) → maximum speed (MAX SPEED) → real-time speed (RT SPEED) → cruising range (RANGE)→ Cumulative mileage (ODO) → riding time (TIME) → single mileage (TRIP) BENELLI BRAVO... -
Page 11: Headlight Switch/Display Mode Switch
Press the “- ” button for 3 seconds, the bike enters walk-assistance mode, the display shows the real-time speed, Pedal Assist level is P . Release the button, the bike exits the walk assistance mode. Brake indication： Braking cut-off shows BENELLI BRAVO... -
Page 12: Technical Documents
6 months of frequent uses. Please contact your dealer for battery replacement. The operating environment is -20℃~60℃. The charging time is about 2-4 hrs. Do not charge the battery for more than 6hrs BENELLI BRAVO... -
Page 13: Storage And Cleaning
W W a a r r n n i i n n g g 1) The user must operate according to the instructions when charging; 2) Never use third party battery or charger for Benelli bikes. 3) When the charger is working, please place it in a safe, well ventilated place, out of reach of children. -
Page 14: Routine Checkup And Maintenance
3. Check front and rear brakes respectively 4. Check if the gear can be changed within the range without abnormal resistance 5. Do not disassemble the bike by yourself unless you have mastered the techniques, so as not to damage other parts. BENELLI BRAVO... - Page 15 . . BENELLI BRAVO...
- Page 16 4. After adjusting the brake, be sure to tighten the brake wire fixing screws 5. Rubber brake pads should not be contaminated with any grease. If they are contaminated with grease, their braking performance will be greatly reduced, and they must be replaced. BENELLI BRAVO...
- Page 17 M7/M8 M7:14/ M8:20 Brake pad Brake cable clamp Brake handle clamp V-type brakes, fastening screws Flywheel fastens screw None Flywheel, lock ring None *The above values are only reference values, please follow the attached parts manufacturer’s operating instructions BENELLI BRAVO...
-
Page 18: Technical Parameters
9. Technical Parameters M M a a n n t t u u s s M M T T B B M M O O D D E E L L D D i i m m e e n n s s i i o o n n s s ( ( L L * * W W * * H H ) ) 1 1 8 8 9 9 0 0 * * 7 7 0 0 0 0 * * 1 1 1 1 4 4 0 0 m m m m W W h h e e e e l l b b a a s s e e 1 1 1 1 6 6 0 0 m m m m... -
Page 19: Warranty Conditions
2. Damage caused by incorrect operations, such as negligent, improper maintenance or incorrect use of the product. 3. Operation of the vehicle when it is overheating 4. Commercial use of the product, such as rental. BENELLI BRAVO... - Page 20 9. Damage caused by servicing of the product (including upgrades and expansions) performed by anyone who is not authorised by Panmi/ Benelli to perform such services 10. Damage caused by nature or acts of God, for example, lightning strikes, cyclones, and the like.
- Page 21 Tampering can void the warranty and render your bike not in compliance with the applicable laws and regulations. To ensure safety, quality and reliability, use only original parts or Benelli authorized replacements for repair and replacement. Benelli is not responsible for any direct, incidental or consequential damages, including, without limitation, damages for personal injury, property damage, or economic losses due to tampering.
-
Page 22: Fault And Troubleshooting
Temperature failure in the battery 0X14 The temperature sensor in the motor is faulty 0x21 Speed sensor failure 0x22 0x23 Headlight failure 0x24 Headlight sensor failure 0x25 Torque sensor torque signal failure 0x26 Torque sensor speed failure 0x30 Communication failure BENELLI BRAVO... - Page 23 Do instructions Obstacles not open the above Other fault or undetermined faults; parts without Motor hub, controller, authorization, or you will charger and battery lose our warranty pack are damaged at the commitment. right time. BENELLI BRAVO...
Need help?
Do you have a question about the Mantus MTB and is the answer not in the manual?
Questions and answers