Table of Contents
Advertisement
Quick Links
FPMA-HAW300
EN
Medical mount
NL
Medische steun
DE
Medizinische Halterung
FR
Support médical
IT
Supporto medico
ES
Soporte médico
PT
Suporte medico
DK
Medicinsk beslag
INSTRUCTION MANUAL
NO
Medisinsk feste
SE
Medicinskt fäste
FI
Medical teline
PL
Uchwyt medyczny
CS
Držák pro lékařské účely
SK
Držiak na lekárske vybavenie
RO
Suport medical
WWW.NEOMOUNTS.COM
Advertisement
Table of Contents
Related Manuals for NewStar Neomounts FPMA-HAW300
Summary of Contents for NewStar Neomounts FPMA-HAW300
- Page 1 INSTRUCTION MANUAL FPMA-HAW300 Medical mount Medisinsk feste Medische steun Medicinskt fäste Medizinische Halterung Medical teline Support médical Uchwyt medyczny Supporto medico Držák pro lékařské účely Soporte médico Držiak na lekárske vybavenie Suporte medico Suport medical Medicinsk beslag WWW.NEOMOUNTS.COM...
-
Page 2: Before Starting Assembly
PARTS FPMA-HAW300 75x75 - 1-3 kg | 115-135 cm 0-115 cm 100x100 mm 2,2-6,6 lbs INDEX Before starting assembly p. 2 Parts p. 3 Arm operation p. 4 Positioning p. 5 Serviceable range p. 6 1. (x1) Wall assembly p. 7 Cable assembly p. -
Page 3: Arm Operation
ARM OPERATION POSITIONING Right view Unit: mm Tighten Loosen Loosen Tighten Loosen Tighten... -
Page 4: Wall Assembly
SERVICEABLE RANGE WALL ASSEMBLY Top view Unit: mm Unit: mm NOTE: use level gauge or protractor to help the wall mount installation SOLID RC WALL 90˚ ± 1˚ 90˚ ± 1˚ 90˚ ± 1˚ If the wall box is not levelled after installation on the wall, please use washers to fill the... - Page 5 STEP 1.1 STEP 1.2 Install the wall mount firmly to a solid wall Place the arm onto the spindle 1. Choose the exact place and height you want to fix the wall mount on the wall and mark the 4 drill holes. 1.
-
Page 6: Cable Assembly
CABLE ASSEMBLY NOTE PARTS Please make sure this joint is in a vertical 90˚ angle. joint cover front cable cover joint cover 90˚ ± 1˚ top cable cover middle cover-1R end cover-2R middle cover-1L end cover-2L VESA cable cover ALLEN KEY COMPARTMENT... - Page 7 STEP 1.1 STEP 1.2 Remove the cable covers. Run the cables through the arm. Assemble the cable wrapper. Carefully slide the cable cover out of the arm slot, as shown. lf the cables are needed to go through the underside of VESA, use the screwdriver to take off the cover.
-
Page 8: Monitor Assembly
MONITOR ASSEMBLY ADJUSTMENT FOR LOADING STEP 1.1 Caution for weight capacity adjustment Fix the monitor on the VESA mount, using a screw driver (not included) and screws. 1. Make sure you have checked the weight of the monitor you wish to mount. 2. - Page 9 REPLACEMENT OF THE ARM COVERS STEP 1.1 STEP 1.3 Follow the order as below to assemble the covers. Replace the adjuster covers as shown. Follow the order as below to assemble the covers. Replace the adjuster covers as shown. STEP 1.2 Press the gas spring downward to level.
- Page 10 ADJUSTING UNIVERSAL JOINT TENSION STEP 1.4 When assembling the arm with monitors of different weight, you may find that the tension of the universal joint needs to be adjusted to ease movement or to maintain the desired monitor position. If so, adjust as follows: Follow the order as below to assemble the covers.
-
Page 11: Safety Notes
SAFETY NOTES • Once assembled do not disassemble. • Make sure that mounting screws are suitable for the vertical surface and adequate to hold the weight of the arm and the monitor. • Support the monitor and arm throughout assembly and mounting. •...
Need help?
Do you have a question about the Neomounts FPMA-HAW300 and is the answer not in the manual?
Questions and answers