Table of Contents
Advertisement
Quick Links
FPMA-HAW100
FPMA-HAW100HC
EN
Medical mount
NL
Medische steun
DE
Medizinische Halterung
FR
Support médical
IT
Supporto medico
ES
Soporte médico
PT
Suporte medico
DK
Medicinsk beslag
INSTRUCTION MANUAL
5 0
0
7 0
5 0
°
1 5
°
4 0
NO
Medisinsk feste
SE
Medicinskt fäste
FI
Medical teline
PL
Uchwyt medyczny
CS
Držák pro lékařské účely
SK
Držiak na lekárske vybavenie
RO
Suport medical
0
9 3
WWW.NEOMOUNTS.COM
Advertisement
Table of Contents
Related Manuals for NewStar Neomounts FPMA-HAW100
Summary of Contents for NewStar Neomounts FPMA-HAW100
- Page 1 INSTRUCTION MANUAL ° ° FPMA-HAW100 FPMA-HAW100HC Medical mount Medisinsk feste Medische steun Medicinskt fäste Medizinische Halterung Medical teline Support médical Uchwyt medyczny Supporto medico Držák pro lékařské účely Soporte médico Držiak na lekárske vybavenie Suporte medico Suport medical Medicinsk beslag WWW.NEOMOUNTS.COM...
-
Page 2: Table Of Contents
PARTS FPMA-HAW100 FPMA- 75x75 - 0-6 kg | 0-170 cm 0-187 cm HAW100: 100x100 mm 0-13,2 lbs FPMA- 75x75 - 6-12 kg | 0-170 cm 0-187 cm FPMA-HAW100HC HAW100HC: 100x100 mm 13,2-26,5 lbs INDEX Before starting assembly p. 2 Parts p. -
Page 3: Arm Operation
ARM OPERATION POSITIONING Right view Unit: mm... -
Page 4: Serviceable Range
SERVICEABLE RANGE WALL ASSEMBLY Range at +20 - Top view Unit: mm Unit: mm SOLID RC WALL NOTE: use level gauge or protractor to help the wall mount installation 90º ± 1º Range at -60 - Top view Unit: mm SOLID RC WALL 90º... - Page 5 STEP 1.1 STEP 1.2 Install the wall mount firmly to a solid wall Only use the drawing on the assembly guide 1. Use a screwdriver to loosen the wall plate and remove the cover. Do not discard the cover after taking it off. 1.
-
Page 6: Cable Assembly
CABLE ASSEMBLY NOTE PARTS Please make sure this joint is in a vertical 90º angle. rotating cover-L 90º± 1º front cable cover 90º ± 1º rotating cover top cable cover middle cover-1R middle cover-1L end cover-2L end cover-2R VESA cable cover-S grab handle... - Page 7 STEP 1.1 STEP 1.3 Removal of the cable covers. Run the cables through the arm. Assemble the cable wrapper. 12. Cable wrapper (x1) 13. Cable tie (x4) Slide the cable cover out of the arm slot carefully, as shown. STEP 1.2 15 cm Remove the VESA cable cover with a...
-
Page 8: Monitor Assembly
MONITOR ASSEMBLY STEP 1.1 Please note that the cable Remove the back cover utilizing a screw driver (not included), as shown and pull out the cable in order to install the monitor. should be placed under the NB. Please save the screws for reattachment of the cover after monitor installation. spring. -
Page 9: Replacement Arm Covers
REPLACEMENT OF THE ARM COVERS STEP 1.3 STEP 1.1 Connect the cable to the monitor Follow the order as below to assemble the covers. Replace the adjuster covers as shown. Connect the cables to the monitor, complete the circuit and replace the VESA cable cover-B or VESA cable cover-S. Fix the cover on the wall mount and tighten the screws. -
Page 10: Adjustment For Loading
ADJUSTMENT FOR LOADING STEP 1.2 Caution for weight capacity adjustment 1. Make sure you have checked the weight of the monitor you wish to mount. Follow the order as below to assemble the covers. Replace the adjuster covers as shown. 2. -
Page 11: Adjusting Universal Joint Tension
ADJUSTING UNIVERSAL JOINT TENSION When assembling the arm with monitors of different weight, you may find that the tension of the universal joint needs to be adjusted to ease movement or to maintain the desired monitor position. If so, adjust as follows: 1. -
Page 12: Safety Notes
SAFETY NOTES • Once assembled do not disassemble. • Make sure that mounting screws are suitable for the vertical surface and adequate to hold the weight of the arm and the monitor. • Support the monitor and arm throughout assembly and mounting. •...
Need help?
Do you have a question about the Neomounts FPMA-HAW100 and is the answer not in the manual?
Questions and answers