Subscribe to Our Youtube Channel
Related Manuals for CreamWare Noah Interpole
Summary of Contents for CreamWare Noah Interpole
- Page 1 Interpole Introduction Interpole Structure and Overview Controls Mode Envelope Follower and ADSR Envelope Follower ADSR Envelope Link Filter - Tactive Instrument Modeller Main Table Of Contents Interpole Contents Index...
- Page 2 It’s all easy for Interpole. great tool for creating exciting Modeling process has been employed. soundscapes from ordinary digital Your CreamWare Team hopes your work This has resulted in the highest-fidelity, sounds, simple mono recordings, or dull with Interpole will be both creative and aliasing-free algorithm by which the ana- sample loops.
- Page 3 Structure and Overview Interpole is a stereo effect consisting of No less important than the envelope stage A ”voltage controlled” amplifier module two identical sections, left and right, for is the LFO. It features six modulation (VCA) follows the filter. The amplifier is the processing of any audio signal.
- Page 4 Controls Interpole possesses a main control panel A text field for the current preset, and an In the upper left corner of the graphic on which all functions are accommodated. icon to open the Preset List are located in surface you’ll find: The panel is divided into sections.
- Page 5 Mode Gate/Envelope External/Internal Selects the basic operating mode of the Interpole has both internal and external The following section describes general envelope section. When Env (Envelope inputs. The signal from the internal inputs settings pertaining to the device, the types Follower) mode is enabled, the envelope passes through the entire signal chain and of modulation, and the operating modes.
- Page 6 Envelope Follower and ADSR As mentioned earlier, the envelope section operates in two modes: Envelope Follower or ADSR Envelope. The controls are arranged such that, so far as is possible, they apply to both modes of operation. However, depending on the mode, other functions—or perhaps no function—are assigned to the controls.
- Page 7 ADSR Envelope The ADSR envelope is enabled when the Gate/Env switch is set to Gate. The gate, which controls the ADSR envelope, is triggered either by a MIDI note-on event or by the Threshold. Select the respective mode with the MIDI/Sens switch. In MIDI mode, the gate is open as long as a MIDI key is held.
- Page 8 Sustain The Sustain level—the level at which the The LFO parameters provide another playground for sound manipulation. Six different signal remains after the attack phase and modulating waveforms are available. The rate can be set manually or controlled by the while the gate is open.
- Page 9 Init Phase Note Determines the position (phase) at which When MIDI synchronization is enabled the the waveform starts when a MIDI note-on speed of the LFO is controlled by Note message is received and Retrig is set to values. A complete oscillation corresponds MIDI.
- Page 10 Link Filter The filter is included in the signal processing chain along with the envelope generator Link Normal/Invert and the LFO. The filter is a 24dB/octave lowpass type also known as a cascading filter. When Link is enabled (see below), the Frequencies below the cutoff remain unprocessed (hence the designation ”lowpass”...
- Page 11 Cutoff Frequency The cutoff frequency is the frequency The ”voltage-controlled” amplifier (VCA) is above which the spectrum is attenuated the last unit in Interpole’s processing chain. (overtones are cut). Set the frequency The VCA follows immediately after the manually here. filter, and is controlled by the envelope and the LFO.
- Page 12 Index ADSR 6 LED 6 saw down 9 ADSR Envelope 7 LFO 3, 8, 10 saw up 9 Attack 6, 7 Link 10 Sens 7 Autopan 10 Link In/Out 8, 10 Sensitivity 6, 7 Link Normal/Invert 10 signal LED 6 low frequency oscillator 2 sine 9 Bend Range 6...
Need help?
Do you have a question about the Noah Interpole and is the answer not in the manual?
Questions and answers