Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JIB 1316B
Summary of Contents for JIB 1316B
- Page 1 MODEL 1316B/1316F FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY...
-
Page 2: Table Of Contents
Table of Contents General safety instructions for Power Tools…………………………………………1 Main specification…………………………………………………………………………2 Unpacking and checking contents…………………………………………………… 2 List of loose parts in the box and bags………………………………………………. 3 Getting to know your drill press………………………………………………………..4 Assembly………………………………………………………………………………….. 5 Lubrication………………………………………………………………………………… 6 Maintenance……………………………………………………………………………… 6 Wire diagram……………………………………………………………………………… 6 Trouble shooting…………………………………………………………………………. -
Page 3: General Safety Instructions For Power Tools
Main Specification Drill Capacity 16 mm / 5/8 in. Chuck Capacity 16 mm / 5/8 in. Swing 330 mm / 13 in. Spindle Taper Spindle Travel 80 mm / 3-5/32 in. Column Diameter 73 mm / 2-7/8 in. Motor 120V/1ph/600W Rack &... - Page 4 ounted...
-
Page 5: List Of Loose Parts In The Box And Bags
List of Loose Parts in the box and bags... -
Page 6: Getting To Know Your Drill Press
Getting to know your drill press - 4-... -
Page 7: Assembly
Assembly Refer to the figure install all parts correctly, tighten the screw and bolts securelly. 1 Base 2. Column/w Support Asm 3 M10*1.5-40Screw (4) 4 Head Asm 5 Table 6 Feed Handle 7 Clamp-Column Lock 8 Crank - 5-... -
Page 8: Lubrication
Lubrication All of the BALL BEARING are packed with grease at the factory.They require no further lubrication. Periodically lubricate the table elevation machanism,the SPLINES (grooves) in the spindle,and the RACK (teeth of the quill),see "Getting to know your drill press." Maintenance Frequently blow out any dust that may accumulate inside the motor. -
Page 9: Trouble Shooting
Trouble Shooting TROUBLE PROBABALE CAUSE REMEDY 1.Incorrect belt tension. 1.Adjust tension. 2.Dry Spindle. 2.Lubricate spindle. Noisy Operation 3.Checking tightness of retaining nut on 3.Loose spindle pulley pulley,and tighten if necessary. 4.Loose motor pulley 4.Tighten setscrews in pulleys. 1.Incorrect speed. 1.Change speed. 2.Chips not coming out of hole. -
Page 10: Repair Parts
Repair Parts FIGURE1 FIGURE1 PARTS LIST Description Description Screw-Hex Soc.Set 11 Support Column M6*1.0-10 12 Screw-Hex HD M10*1.5-40 Collar-Rack 13 Screw-Hex Soc.Set Gear-Helical M10*1.5-12 Crank 14 Tube Column Table 15 Rack Clamp-Table 16 Clamp-Column Screw-Hex HD 17 Support Table w/Indicator M16*20-35 18 Worm-Elevation Arm-Table w/Scale... - Page 11 Repair Parts FIGURE2 FIGURE2 PARTS LIST Description Nut-Lock Ring-Locking Washer Bearing-Ball 17mm Washer-Rubber Tube-Quill Key-Chuck Chuck Arbor Key-Drift Spindle Bearing-Ball...
- Page 12 Repair Parts FIGURE3 FIGURE3 PARTS LIST Description Description Ring-Retaining 10 Screw-Set M10*1.5-12 Bearing-Ball 25mm 11 Pulley-Motor Spacer-Bearing 12 Knob Belt-"V" M24 13 Screw-Pan HD M5*0.8-12 Nut-Pulley 14 Pivot-Ldler Pulley-Spindle 15 Pully-Center Insert-Pulley 16 Bearing-Ball 15mm Guard-Pulley w/Labels 18 Washer Foam Screw-RD HD Washer 19 Lock Washer Ext.M6 M6*1.0-16...
- Page 14 FIGURE4 PARTS LIST Description Description knob-Motor Adjusting 23 Seat-Spring Screw-Socket Set M10*1.5-12 24 Retainer-Spring Handle-Belt Tension 25 Spring-Torsion Pin-Stop 26 Cap-Spring Ring-Depth Stop W/Scale 27 Nut-Hex M12*1.5-8 Lock-Depth Screw 28 Head w/Pointer and Trim 32 Tie-Wire Guide Scale 33 Cord-Power w/Plug Knob 36 Clamp-Cord 10 Rod...