Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Loveshaw LITTLE DAVID LDXCRS
Summary of Contents for Loveshaw LITTLE DAVID LDXCRS
- Page 1 MANUAL OWNERS LDXCRS THE LOVESHAW CORPORATION LOVESHAW - EUROPE 2206 EASTON TURNPIKE UNIT 9, BRUNEL GATE SOUTH CANAAN, PA 18459 W. PORTWAY INDUSTRIAL ESTATE ANDOVER, HAMPSHIRE SP103SL TEL: (570) 937-4921 ENGLAND FAX: (570) 937-4370 44-264-3575-11...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SUBJECT GENERAL SAFETY PRECAUTIONS MACHINE LABELS MACHINE SPECIFICATIONS INTRODUCTION INSTALLATION OPERATION MAIN FRAME HEAD ELECTRICAL SYSTEM LUBRICATION TROUBLE - SHOOTING TAPE CARTRIDGE WARRANTY ILLUSTRATED REPLACEMENT PARTS TABLE OF CONTENTS LOVESHAW an ITW Company... -
Page 3: General Safety Precautions
OF THE SHORT AXIS. SEE FOOTPRINT DRAWING. MACHINE LABELS (SEE NEXT PAGE) ARE PLACED ON THE MACHINE FOR YOUR SAFETY. LABELS SHOULD BE INTACT AND LEGIBLE. REPLACE LABELS IF THEY ARE WORN, DAMAGED, PEELING, OR ILLEGIBLE. LOVESHAW an ITW Company... -
Page 4: Machine Specifications
NUMBER OF BOXES/MIN.: VARIES WITH BOX SIZE CLOSURE MATERIAL - PRESSURE SENSITIVE TAPE WIDTH: 1.5 inches to 38 mm to 2 inches 50 mm MAX. ROLL DIAMETER: 15 inches 380 mm WEIGHT: (uncrated) 180 lbs. 81 kg. LOVESHAW an ITW Company... -
Page 5: Introduction
INTRODUCTION THE LITTLE DAVID LDXCRS UNIFORM PRESSURE SENSITIVE TAPER IS DESIGNED TO TAPE TOP AND BOTTOM FLAPS OF A WIDE VARIETY OF BOX SIZES. AFTER MANUALLY ADJUSTING THE MACHINE FOR THE BOX SIZE, THE OPERATOR ONLY HAS TO FOLD THE FLAPS AND PUSH THE BOX INTO THE MACHINE AFTER WHICH THE MACHINE WILL TAPE THE TOP AND BOTTOM FLAPS AND DISCHARGE THE BOX. -
Page 6: Installation
TO FEEDING THE BOXES IN THE MACHINE. A CONVEYOR SHOULD BE PROVIDED AT THE OUT FEED END OF THE MACHINE TO RECEIVE THE BOXES AS THEY ARE DISCHARGED FROM THE MACHINE. IMPORTANT: BE SURE THE TABLE AND CONVEYOR ARE 1/4” (6 mm) BELOW THE MACHINE BELT HEIGHT. LOVESHAW an ITW Company... -
Page 7: Operation
OF THE BOX, SHOULD FEED THE BOX INTO THE MACHINE UNTIL THE BELTS TAKE IT FROM HIM. THE MACHINE WILL SEAL THE TOP AND BOTTOM FLAPS AND DISCHARGE THE BOX TO THE OUT FEED CONVEYOR AUTOMATICALLY. LOVESHAW an ITW Company... -
Page 8: Main Frame
CLOSE HANDLE MAKING SURE NOT TO OVER TENSION BELTS. EACH BELT IS REPLACED SEPARATELY, HOWEVER, IT IS RECOMMENDED THAT BOTH BELTS BE REPLACED AT THE SAME TIME. IT IS IMPORTANT THAT FACTORY SUPPLIED BELTS BE USED SINCE THEY ARE OF SPECIAL CONSTRUCTION. LOVESHAW an ITW Company... -
Page 9: Head
THE MOTOR AND FRAME ARE GROUNDED THROUGH THE ELECTRICAL CONNECTOR. THE CIRCUIT BREAKER IS FACTORY SET. IF IT TRIPS, IT SHOULD BE RESET AFTER INSPECTION OF THE ELECTRICAL SYSTEM. WARNING: THE INSPECTION OF THE ELECTRICAL SYSTEM SHOULD BE DONE BY A QUALIFIED ELECTRICIAN ONLY! LOVESHAW an ITW Company... -
Page 10: Lubrication
ALL MECHANICAL PARTS ON THE LITTLE DAVID ARE PERMANENTLY LUBRICATED AND SEALED BEARINGS ARE USED THROUGHOUT. THE REDUCER IS A SEALED UNIT. THE MAST SHOULD BE CLEANED AND SPRAYED WITH A SILICONE LUBRICANT - THIS SHOULD BE DONE ON A WEEKLY BASIS TO ENSURE FREE MOVEMENT OF THE HEAD. LOVESHAW an ITW Company... -
Page 11: Trouble Shooting
CHECK THE DRAG OF THE TAPE. TOO MUCH DRAG MAY CAUSE OVERRUNNING OF THE TAPE ROLL. ADJUST THE TAPE CORE DRAG SETTING. TAPE TENSION SET TOO HIGH. CHECK ROLLER STOP INSIDE CARTRIDGE. CHECK THAT THE TAPE IS PROPERLY THREADED AND THAT TAPE CORE IS PROPERLY CENTERED. LOVESHAW an ITW Company... - Page 12 IF KNIFE STOP BLOCK IS CAUSING FRICTION ON KNIFE STUDS, ROTATE UNTIL FREE. TAPE TENSION IS SET TOO LOW. TAPE NOT CENTERED ON BOX: USE SCREW IN CENTER OF TAPE CORE TO RE-ALIGN. TAPE NOT BEING WIPED: CHECK MAIN SPRING. TAPE TENSION IS SET TOO HIGH. LOVESHAW an ITW Company...
- Page 13 RAISE HEAD SLIGHTLY. CHECK BELT TENSIONING. INCREASE IF NECESSARY. BOX SLIPS AGAINST BELTS: LOWER HEAD SLIGHTLY TO INCREASE PRESSURE ON BOX. BELTS RUB AGAINST FRAME: CHECK THAT BELTS ARE POSITIONED CORRECTLY IN BETWEEN THE BELT GUIDE. LOVESHAW an ITW Company...
-
Page 14: Tape Cartridge
THE SMALL NUT ON THE KNIFE ARM STUD AND ROTATING THE STUD UNTIL THE LARGE NUT CONTACTS THE BUMPER AT THE DESIRED SETTING. KNIFE ARM TENSION IS CONTROLLED BY THE COMPRESSION SPRING ON THE STUD. TIGHTEN THE NYLOK NUT FOR GREATER TENSION. ALWAYS POWER DOWN MACHINE FIRST. LOVESHAW an ITW Company... - Page 15 RAISE REAR OF CARTRIDGE AND MOVE CARTRIDGE UP AND OUT OF MACHINE. THREADING IS THE SAME AS TOP CARTRIDGE. GRABBING THE CARTRIDGE BY REAR ROLLER AND FRONT SHAFT, ANGLE FRONT OF CARTRIDGE ONTO MOUNTING BOLTS AND THEN LOWER REAR OF CARTRIDGE. LOVESHAW an ITW Company...
- Page 16 LOVESHAW UNDER THIS WARRANTY IS STRICTLY LIMITED TO THE COST OF REPAIRING OR REPLACING, AS LOVESHAW MAY ELECT, ANY PART OR PARTS THAT PROVE IN LOVESHAW’S JUDGMENT TO HAVE BEEN DEFECTIVE IN MATERIAL OR WORKMANSHIP AT THE TIME THE GOODS WERE SHIPPED FROM LOVESHAW’S PLANT. ANY WARRANTY CLAIM NOT MADE IN WRITING TO LOVESHAW AT ITS HOME OFFICE WITHIN THE APPLICABLE WARRANTY PERIOD AND WITHIN 10 DAYS OF FAILURE WILL NOT BE VALID.
-
Page 17: Illustrated Replacement Parts Table Of Contents
FRAME ASSEMBLY HEAD ASSEMBLY MAST ASSEMBLY TOP SQUEEZER ASSEMBLY SIDE RAIL ASSEMBLY BELT DRIVE ASSEMBLY BELT TENSION ASSEMBLY ELECTRICAL ASSEMBLY ELECTRICAL BOX ASSEMBLY MOTOR ASSEMBLY INFEED TABLE ASSEMBLY EXIT TABLE ASSEMBLY LEVELER PAD ASSEMBLY CASTER ASSEMBLY LOVESHAW an ITW Company... - Page 18 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED...
- Page 19 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE = .3mm METRIC FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE MATERIAL CHECKED...
- Page 20 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED...
- Page 21 DWG NO SCALE LDW-0129-3 BOLT, SIDE RAIL METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED MATERIAL REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER (SS) - DENOTES STAINLESS STEEL PART.
- Page 22 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED...
- Page 23 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED...
- Page 24 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE CHECKED MATERIAL...
- Page 25 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE CHECKED MATERIAL...
- Page 26 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO FLWMKS LOCK WASHER SPRING M16 METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE MATERIAL NOTED CHECKED...
- Page 27 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE CHECKED MATERIAL...
- Page 28 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE CHECKED MATERIAL...
- Page 29 THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED...
- Page 30 DWG NO SCALE LDW-0053-4 ROD, LEVELING METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED FHJMSRS HEX JAM NUT 3/4-10...
- Page 31 DWG NO SCALE ITEM PART NUMBER DESCRIPTION METRIC = .3mm FINISH LOVESHAW-ITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY .XXX = .1mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED CHECKED OPC511 CASTER - SWIVEL...
Need help?
Do you have a question about the LITTLE DAVID LDXCRS and is the answer not in the manual?
Questions and answers