Related Manuals for Huck POWERIG 940-220
Summary of Contents for Huck POWERIG 940-220
- Page 1 NSTRUCTION ANUAL 940-220 940-220 ODEL ODEL POWERIG ® H YDRAULIC 02-13-2012 HK604...
- Page 2 940-220 Powerig® Alcoa Fastening Systems (HK604) NOTICE: This instruction manual applies only to HUCK ® Powerig Model 940-220 with serial number 1191 and above.
-
Page 3: Table Of Contents
940-220 Powerig® Alcoa Fastening Systems (HK604) ONTENTS ONTENTS ..........4 AFETY . -
Page 4: Afety
Reasonable care of installation tools by operators is an beginning of each shift/day for damage or wear. Any repair important factor in maintaining tool efficiency, eliminating should be done by a qualified repairman trained on Huck pro- downtime, and in preventing an accident which may cause cedures. -
Page 5: Description
The four-way directional valve is operated by a 24 electrically operated power source designed to oper- volt AC control circuit. The high pressure relief ate all Huck hydraulic installation equipment exclud- valve controls PULL pressure (maximum pressure of ing HUCK-SPIN tools. -
Page 6: Specifications
940-220 Powerig® Alcoa Fastening Systems (HK604) PECIFICATIONS PECIFICATIONS Width 16.1 (40.9 cm) Length 13.9 (35.4 cm) Height 18.5 (47.0 cm) Weight (without fluid) 66 lbs. (30 kg) Reservoir Capacity 2.6 gallons (10 liters) Electrical System 220 volts, 50/60 hertz, single phase, AC Control System Solenoid operated directional valve, 24 volts Motor 12,000 RPM, 1-1/8 HP, 20 amps nominal... -
Page 7: Principle Of Operation
Pressurized fluid is directed to the RETURN ® 940-220 Powerig pressure port of the installation equipment. The motor contactor is held closed until the HUCK INTL. INC. 590312 ® REV C U.S. Registration preset RETURN pressure is reached and pres- sure switch (PS) contacts open. -
Page 8: Aintenance
(HK604) PERATION PERATION Each time before using the Powerig Hydraulic Unit: Connect a Huck hydraulic tool to the Powerig Hydraulic Unit using a hose kit. 1. Check the fluid level in the reservoir and add hydraulic fluid as required. Be sure that: 2. -
Page 9: Hecking And
(minimum) amp wall outlet. manual for pressure rating. WARNING: If recommended maximum 2. Plug an auxiliary trigger (optional HUCK part num- pressure is exceeded, violent failure of ber 113056) into the outlet on the Powerig fastening system may occur. This may Hydraulic Unit control panel. -
Page 10: Spare Parts
A click available in most localities. A handy tube of can be heard. LUBRIPLATE 130AA is available from Huck as part number 502723. 10. Continue tightening the switch adjustment screw 1/8 of a turn after the switch button actuates. -
Page 11: Rawing
940-220 Powerig® Alcoa Fastening Systems (HK604) Figure 3... -
Page 12: Ssembly Drawing
940-220 Powerig® Alcoa Fastening Systems (HK604) Figure 4... -
Page 13: Ssembly Drawings
940-220 Powerig® Alcoa Fastening Systems (HK604) Figure 5... - Page 14 940-220 Powerig® Alcoa Fastening Systems (HK604) Figure 6...
-
Page 15: Ssembly Drawing
940-220 Powerig® Alcoa Fastening Systems (HK604) RESSURE WITCH ETAIL RESSURE WITCH ETAIL Figure 7... -
Page 16: Troubleshooting
A "T" gauge is available for use when checking and Heavy duty steel dolly for easy movement of rig adjusting pressures, and troubleshooting. throughout the work area. Hose and Control Cord Kits of various lengths Please contact your HUCK representative. - Page 17 Huck shall not be liable for any loss or damage result- THERE ARE NO WARRANTIES WHICH EXTEND ing from delays or nonfulfillment of orders owing to...
- Page 18 Huck’s written quotations, acknowledge‐ International. Huck provides technical assistance ments, and/or purchase orders. It is recommend‐ regarding the use and application of Huck fasten‐ ed that the user secure specific, up‐to‐date data ers and tooling. and information regarding each application and/or use of such products.
Need help?
Do you have a question about the POWERIG 940-220 and is the answer not in the manual?
Questions and answers