Related Manuals for FLI ACTIVE
Summary of Contents for FLI ACTIVE
- Page 2 Mounting Guidelines Your FLI enclosure is designed with a swift installation routine in mind. Please mount it in a dry location on a solid surface. NEVER mount the enclosure at such an angle that the amplifier is upside down, this will cause the amplifier to over heat and will eventually damage the entire unit.
- Page 3 ● Ground Cable The ground cable needs to carry the same current as the power cable. Again at least an 10 ● gauge cable should be used. The amplifier ground should be connected directly to the chassis of the vehicle, to bare ● metal. (not painted surface) The cable length should be kept to an absolute minimum. ● It is not recommended that you connect the ground cable to the vehicles seatbelts. ● Remote Turn On A minimum of 18 gauge cable should be used for this connection. ● The cable should be run with exactly the same care and attention as the power cable and ● taken back to the source and joined to the remote cable provided on the head unit. If the headunit does not have a remote turn on cable then a 12v supply should be used. This ● will require a switch to be fitted inline to enable the amplifier to be turned on and off. NOTE: Remember that if this switch is left on you will flatten the car battery. RCA Cables A pair of RCA cables should be run from the head unit to the FLI amplifier. ● Please take extra care when running these cables from the source to the amplifier. Ensure ● that they are placed away from all items that can generate any interference, wiring harnesses etc. It is recommended that the RCA cables should be run on the opposite site of the car to the ● previously installed power cables. ...
- Page 4 Set Up Section Gain Control Setting To correctly set the gain control of the amplifier to match that of the source (headunit) use the following setup routine: Turn the gain control to minimum on the amplifier. ● On the headunit set all crossovers to flat and both bass and treble to zero. ● Turn up the source (headunit) to approx 3/4 volume. ● Very slowly turn up the gain on the amplifier until distortion can be heard in any of the ● speakers or until the volume reaches an uncomfortable listening level when this is reached turn down the gain control slightly. The gain control is now set. Crossover Setting All FLI active enclosures come with a built in Frequency Control. This will allow you to set the frequency at which the amplifier filter will take affect.It is variable from 40 Hz - 250 Hz. 40 Hz will produce only low frequencies, very deep bass. Whilst 250 Hz will produce low and higher punchy bass frequencies. In the correct set up the bass should not be overly prominent, although some users may wish to have a bigger bass presence. To set this correctly follow the following routine: Firstly set the gain control correctly as described above. ● Play a known piece of dynamic music through the entire system. ● Use the Frequency Control to blend the frequencies from the subwoofer into the rest of the ● vehicle so that the bass coming from the enclosure disappears' or blends in with the rest of the car speakers. The crossover is now set. Troubleshooting Before removing the amplifier, refer to the list below and follow the suggested procedures. ● If in any doubt get help from a car audio installation expert or qualified auto electrician.
- Page 5 Features Variable Gain Control 40 – 250 Hz variable 12 dB crossover Specification Input sensitivity 40 mV Continuous Power 10 V – 14.4 V Signal / Noise Ratio > 100dB In order to protect your purchase and aid your warrantee please fill in the following form and keep it safe for your future reference: Model Number: Serial Number: Purchased From: Date of Purchase:...
- Page 7 Accessories can be ordered separately from the FLI website www.fliaudio.co.uk Only available in the UK If outside uk please contact your dealer or distributor from the FLI website FLI In dash Remote control Allows 24dB gain adjustment of the bass boost feature which is present on all FLI Loaded amplifers £14.99 Line Level Convertor Convert your speaker wire into an RCA connection. Can be used off your rear speakers or directly from headunit £14.99 10 Gauge FLI wiring kit features all you need to wire your FLI LOADED amplifiers £19.99 FLI 1 Farad digital powe capacitor The FLI power cap will delivery its large current reserve quicker than any battery, meaning solid bass response on any FLI system £79.99 FLI baseball cap high quality cool grey baseball cap £9.99 FLI T-shirt Cool grey tshirt with logo on front and big logo on back comes in medium , large & xlarge £9.99 Order online or call sales on 0870 765 8423 . All items above come with free next day delivery.
-
Page 8: Limited Warranty
All content included in this manual such as text, graphics, logos, icons, images data, the selection and arrangement thereof, are the property of FLI Audio (herein referred to as "FLI", "us" or "we") and its affiliate or their content and technology providers, and are protected by United Kingdom and International copyright laws.