Related Manuals for Optical Systems Design OSD8327 Series
Summary of Contents for Optical Systems Design OSD8327 Series
-
Page 1: Index
OPERATOR MANUAL OSD8327 SERIES HD/SDI AND DATA TX/RX FIBER OPTIC TRANSMISSION SYSTEM... -
Page 3: Table Of Contents
OPTICAL SYSTEMS DESIGN INDEX 1 TECHNICAL SUMMARY ......................4 BRIEF DESCRIPTION ......................4 1.1.1 OVERVIEW............................. 4 1.1.2 APPLICATIONS............................4 1.1.3 FEATURES AND BENEFITS ......................... 4 TYPICAL CONFIGURATION ....................5 TECHNICAL SPECIFICATIONS ................... 6 INSTALLATION AND OPERATION ..................7 INTRODUCTION ........................7 INSTALLATION ........................ -
Page 4: Technical Summary
1.1.1 OVERVIEW The OSD8327 series is a high-quality fiber optic serial digital video (SDI) and data transmission system. The system consists of the OSD8327T transmitter and the OSD8327R receiver, which are designed to be used as a pair to reliably transport SDI and duplex serial data over fiber for long distances using 1310nm, 1510nm and CWDM wavelengths. -
Page 5: Typical Configuration
OPTICAL SYSTEMS DESIGN TYPICAL CONFIGURATION Figure 1 below indicates the typical set-up for an OSD8327 system. OSD8327T OSD8327R HD/SDI Signal Monitor with 1 Fiber Source HD/SDI Interface λ λ Data Data 2 Fiber OSD8327T OSD8327R HD/SDI Signal Monitor with Source... -
Page 6: Technical Specifications
OPTICAL SYSTEMS DESIGN TECHNICAL SPECIFICATIONS TABLE 1: TECHNICAL SPECIFICATIONS SPECIFICATION PERFORMANCE Input/Output Impedance 75Ω Input/Output Levels 800mVpp nominal 350m @ 270Mbps Coax Equalization 140m @ 1.485Gbps 70m @ 2.97Gbps SDI Connectors BNC Female Sockets Data Rate DC to 1Mbps NRZ Pulse Distortion and Jitter <±0.3µsec over full dynamic range... -
Page 7: Installation And Operation
OPTICAL SYSTEMS DESIGN 2 INSTALLATION AND OPERATION INTRODUCTION This section outlines the methods required to install and operate the OSD8327T and OSD8327R successfully. It should be studied carefully if damage to the equipment or poor results are to be avoided. -
Page 8: Osd8327 Drawings And Dimensions
OPTICAL SYSTEMS DESIGN 2.2.3 OSD8327 DRAWINGS AND DIMENSIONS The OSD8327T and OSD8327R are designed to be mounted on an even surface and to be secured by means of M4 or smaller screws. The OSD8327T and OSD8327R card versions are designed to be inserted into a chassis and secured by means of captivated screws. -
Page 9: Power Supply Connections
OPTICAL SYSTEMS DESIGN 2.2.4 POWER SUPPLY CONNECTIONS The OSD8327T and OSD8327R require external DC power. The voltage range is +10 to 28V Power should be connected to the power socket located on the front panel of the units and applied as indicated below;... -
Page 10: Optical Connections
OPTICAL SYSTEMS DESIGN The OSD8327R has two HD/SDI BNC output connectors. Note: Figure 5 drawing shows the module version. The card version is identical except the power connector being a DB9. HD/SDI Monitor HD/SDI Monitor FIGURE 5: OSD8327R VIDEO CONNECTIONS 2.2.6... -
Page 11: Data Connections
OPTICAL SYSTEMS DESIGN 2.2.7 DATA CONNECTIONS Data signals are connected to the 8-way terminal block connector as set out in Table 3 TABLE 3: DATA CONNECTOR PIN ASSIGNMENTS 8 WAY DATA FUNCTION TERMINAL BLOCK GROUND RS232 OUTPUT RS232 INPUT RS422 OUTPUT - / RS485 (4W OUTPUT -) -
Page 12: Osd8327 Switch Operation
OPTICAL SYSTEMS DESIGN OSD8327 SWITCH OPERATION The OSD8327 has an 8-way switch for control of data functions and video functions. These will be described in two sections, namely HD/SDI video control and data control. 2.3.1 HD/SDI VIDEO SWITCH SETTINGS The OSD8327T has an Automatic Equalizer (SW8) and Reclocker (SW7) switch located on the front panel. -
Page 13: Data Switch Settings
OPTICAL SYSTEMS DESIGN 2.3.2 DATA SWITCH SETTINGS Six (SW1 to SW6) of the 8-way control switches are used for data control. The 8-way switch is located at the front of OSD8327 modem. STD 232/485 Bias Delay Delay Delay RS232/422/485 FIGURE 9: DATA MODE SWITCH SETTINGS... -
Page 14: Led Indicator Operation
OPTICAL SYSTEMS DESIGN LED INDICATOR OPERATION 2.4.1 OSD8327T INDICATORS Transmit Data Not Used Laser OK 270Mbps Carrier Present Not Used Locked SDI Data Rate Not Used 1485Mbps 2970Mbps Receive Data FIGURE 10: OSD8327T LED INDICATORS TABLE 8: OSD8327T LED INDICATORS... -
Page 15: Osd8327R Indicators
OPTICAL SYSTEMS DESIGN 2.4.2 OSD8327R INDICATORS >-24dBm >-18dBm >-12dBm Transmit Data >-6dBm >-0dBm Not Used Carrier Present Locked 270Mbps Optical Signal Loss Not Used Not used 1485Mbps 2970Mbps Receive Data FIGURE 11: OSD8327R LED INDICATORS TABLE 9: OSD8327R FRONT PANEL INDICATOR FUNCTIONS... -
Page 16: Maintenance
OPTICAL SYSTEMS DESIGN 3 MAINTENANCE INTRODUCTION The following section outlines the fault-finding procedure for the OSD8327T and OSD8327R modems. Please take note of the following: Personnel without appropriate training should not attempt any maintenance except that outlined ▲ below. If further maintenance is attempted you are warned that every care should be taken to ensure that ▲... -
Page 17: Warranty
For warranty period, please call your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. - Page 20 Optical Systems Design Pty. Ltd. OPTIC L 7/1 Vuko Pl. Warriewood 2102 P.O. Box 891 Mona Vale N.S.W. Australia 2103 SYSTEMS Telephone: +61 2 9913 8540 Facsimile: +61 2 9913 8735 Email: sales@osd.com.au DESIGN Web Site: www.osd.com.au PTY LTD A.B.N. 83 003 020 504...
Need help?
Do you have a question about the OSD8327 Series and is the answer not in the manual?
Questions and answers