Table of Contents
Advertisement
Quick Links
Design, manufacture, sales & service
of pneumatic tools
OPERATION AND MAINTENANCE MANUAL
IMPORTANT SAFETY INFORMATION ENCLOSED. READ THIS MANUAL BEFORE
OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION IN
THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PERMON s.r.o.
Roztoky
27023 Křivoklát
CZECH REPUBLIC
SK 9-5, SK 9-6, SK 9-6A,
SK 13B, SK 13D, SK 13DZ
SEIT 1826 - SINCE 1826
tel:
+420 (0)313 558145
+420 (0)313 558271-4
fax:
+420 (0)313 558313
export@permon.cz
email:
www.permon.cz
Advertisement
Table of Contents
Related Manuals for Permon SK 9-5
Summary of Contents for Permon SK 9-5
- Page 1 Design, manufacture, sales & service SEIT 1826 - SINCE 1826 of pneumatic tools OPERATION AND MAINTENANCE MANUAL SK 9-5, SK 9-6, SK 9-6A, SK 13B, SK 13D, SK 13DZ IMPORTANT SAFETY INFORMATION ENCLOSED. READ THIS MANUAL BEFORE OPERATING TOOL. IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
-
Page 2: Using The Tool
SK 9-5, SK 9-6, SK 9-6A, SK 13B, SK 13D and SK 13DZ Pick Hammers are designed for the disintegration of low to medium strength materials (e.g. concrete, masonry bituminous asphalt etc). Permon is not responsible for customer modifications of tools for applications on which Permon was not consulted. -
Page 3: Operation
• Keep hands and fingers away from the throttle lever until it is time to operate the tool. • Never rest the tool or chisel on your foot. • Never point the tool at anyone. • Compressed air is dangerous. Never point an air hose at yourself or co–workers. •... -
Page 4: General Instructions
3. Insert chisel into the hammer. 4. Screw on firmly the retainer. For Latch Type Retainer: 1. Operate the Latch until it is approximately 90 degrees to the body of the tool and clicks into position. 2. Insert the accessory into the tool until the collar of the accessory is past the Latch. 3. - Page 5 An air cushion is present if the piston “bounces”, at the bottom of the cylinder and no metal to metal contact noise can be heard. If a cushion is not present contact your authorised Permon repair centre for advise. Cylinder assembly Grip the cylinder (1) vertically in a vice protected with leather or copper covered vice jaws.
- Page 6 Handle assembly Position trigger (25) in its slot in the handle body and align the holes in each part. Drift or press home the trigger pin (26). Check the throttle lever is free to move easily. Grip the handle body (24) in a vice protected with leather or copper covered vice jaws. Lubricate and insert throttle pin (32) into position reduced diameter out of the hole.
-
Page 7: Specifications
SPECIFICATIONS SK 9-5 SK 9-6 SK 9-6A Weight Length Width Max. Working Pressure Air Consumption /min Impact Rate 1/min 1620 1620 1620 φ25x75 Chuck Size 22 hex. x 82 22 hex. x 82 Vibration Level 13,32 m/s 13,32 m/s 13,32 m/s... -
Page 9: Parts List
PARTS LIST Ref. Part No. Part Name Qty. 9410350 Pickhammer SK 9-5 9410360 Pickhammer SK 9-6 9410430 Pickhammer SK 9-6A 9410490 Pickhammer SK 13-B 9410500 Pickhammer SK 13-D 9410510 Pickhammer SK 13-DZ 8323590 8323860 Cylinder Assy. R25x75 2005280 2001610 Nozzle R25x75...