IHP UZY-7-B Installation Instructions

INSTALLATION INSTRUCTIONS FOR INSTALLING UZY-7-B REPLACEMENT BLOWER KIT
FOR USE WITH WOOD-BURNING FIREPLACES LISTED IN TABLE 1
KIT CONTENTS
2 ea. UZY-7-B Blower Assembly
1 ea. Mill-Pack
1 ea. Instruction Sheet
TOOLS NEEDED
Robertson (square) or Phillips (star) screwdriver
Cat. No. Model
J8005 UZY-7-B Montecito Estate™, WCT6840WS and BIS
Table 1
GENERAL INFORMATION
This blower kit can easily be installed when the fireplace has a pre- installed
junction box with 3 prong receptacle. You just have to plug it in.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact your local distributor
or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
The blower must be plugged directly into a properly grounded
three-prong receptacle, 120 VAC, 60 Hz, single phase. Do not
cut or remove the grounding prong from this plug.
Installation must be in accordance with National Electrical
Code, ANSI/NFPA 70 - latest edition. In Canada, the current
CSA C22.1 Canadian Electrical Code - latest edition.
The blowers have magnetic blower mounts. The junction box (factory
installed on approved fireplaces for the use of this blower kit) must be
connected to 120 VAC service before permanently enclosing the fireplace.
The access hole for connecting the 120 VAC is located on the lower
back right exterior side of the fireplace.
CAUTION: Should this blower kit require servicing, the power supply
must be disconnected.
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor
for fireplace code information.
Printed in U.S.A. © 2015 Innovative Hearth Products
P/N 900600-00 Rev. NC 10/2015
Blower Kit
Where Used
®
WARNING
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
P/N 900600-00
Rev. NC, 10/2015
These fans do not need regular maintenance however, periodic cleaning
is required. Check the area under the firebox and in front of the fans
and wipe or vacuum at least once a month during the operating season.
INSTALLATION INSTRUCTIONS
Step 1. Remove (2) hinge bolts from the (2) hinges, then remove the
door. Then repeat on the other side.
Step 2. Remove (8) decorative caps and then remove the (8) screws
that are under the decorative caps on the facade. Then remove
the façade.(Figure 1).
Step 3. Remove the screw located below the blower motor that holds it
to the back of fireplace.
Tradition
Step 4. Pull the blowers out of the unit through the square hole located
in the front bottom right corner.
Step 5. Place the blower kit into the unit through the square hole located
in the front bottom right corner.
Step 6. Install the thermo-disk fan activator under the firebox toward
the right side, if necessary.
Step 7. Replace facade, by securing it with the (8) screws and then place
decorative caps over the screws on the facade.
Step 8. Place door back on hinges, where the hinge holes line up, and
then secure door by placing hinge bolt through the holes. Repeat
on the other side.
Figure 1
Figure 2
HEARTH PRODUCTS
KITS AND ACCESSORIES
UZY-7-B BLOWER KIT
Rivnut (1)
Fireplace Front (2)
Decorative Facade (3)
Decorative Cap (4)
Facing Screw (5)
1
2
3
4
5
Innovative Hearth Products
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
*
Blower Space
1