Advertisement
Available languages
Available languages
6.
Slide the hinge pin (711-04988) into
the hole located on the mounting tab,
as shown in Figure 13. Use the cut-out
window (see inset in Figure 13) to line
up the hinge pin on the other side and
push pin all the way in until it reaches
the end-stop. At this point the pin clips
into place and is secured by a tab in
the bagger cover. See Figure 14.
7.
Open bagger cover by pushing in on
the rear, right-side tab with your right
hand (1), and lifting the cover with
your left hand in the center rear of
the bagger cover (2) as shown in
Figure 15.
8.
Install both grass bag assemblies
(664-05104) onto the hanger
assembly rails by inserting the front
edge in first (1), and then setting the
back edge down until it fits into the
assembly (2), as shown in Figure 16.
Figure 15
Installing the Boot Rod & Hardware
Model 19B70054*:
1.
From the inside of the boot, put the two
hex head screws (738-1225), from
hardware pack 689-00636, through the
holes at the bottom front of the boot.
See Figure 17.
2.
Put the mounting rod (747-06043) in
place over the hex head screws. Make
sure the tip of the rod is facing out from the boot. See Figure 17.
3.
Begin threading the two flange lock nuts (712-04064) onto the hex head
screws. See Figure 17.
4.
Using a 7/16-inch wrench or socket on the screw and a 7/16-inch box wrench
on the lock nuts, tighten down so flange is flush to secure the assembly.
Model 19B70055*:
1.
From the inside of the boot, put the
two hex head screws (738-1225), from
hardware pack 689-02199, through the
holes at the bottom front of the boot. See
Figure 18.
2.
Put the mounting rod (747-06309) in
place over the hex head screws. Make
sure the tip of the rod is facing out from
the boot. See Figure 18.
3.
Begin threading the two flange lock nuts (712-04064) onto the hex head
screws. See Figure 18.
4.
Using a 7/16-inch wrench or socket on the screw and a 7/16-inch box wrench
on the lock nuts, tighten down so flange is flush to secure the assembly.
ASSEMBLY & INSTALLATION
Figure 13
Figure 14
1
2
Figure 16
Figure 17
Figure 18
7
Installing the Boot - 42"/46"
Double Bagger
1.
With the tractor's discharge chute
raised up and held open (1), install the
boot by placing the boot mounting
rod into the chute mounting tab (2),
as shown in Figure 19.
2.
Secure the boot to the deck using
a wing knob (720-04122) from
hardware pack 689-01419. See
Figure 20.
NOTE:
If present, remove the protective cap off of the mounting stud on the mowing deck as
shown in the upper inset of Figure 20.
IMPORTANT!
Be certain that the bottom of the discharge chute is located inside of the lip of
the deck opening, as shown in Figure 21.
1
2
Figure 20
Installing the Boot - 50"/54" Double Bagger
When installing the boot, two different installation instructions exist. For the 54-
inch fabricated deck units, the boot mounts directly onto the cutting deck. For the
50-inch and 54-inch stamped decks, an adapter must first be installed. Be sure to
follow the instructions that pertain to the unit you are installing this bagger on.
54" Fabricated Deck Units:
1.
Raise the deck to its highest position.
2.
Raise the chute deflector (1 in
Figure 22) on the deck and hold it
while you position the boot over
the chute opening.
3.
Insert the end of the boot (2) into
the hole provided in the deck wheel
mount as shown in the inset of
Figure 22.
4.
Pivot the boot until the hole in the
boot aligns with the pin on the deck.
Move the boot down onto that pin as
shown in (3) of Figure 22.
5.
Secure the boot to the cutting deck
using a wing knob (720-04122) from
hardware pack 689-01419. Refer to
Figure 23.
1
2
Figure 19
Figure 21
1
3
2
Figure 22
Figure 23
Advertisement
