Subscribe to Our Youtube Channel
Related Manuals for MyBinding SealerSales W-300DAT
Summary of Contents for MyBinding SealerSales W-300DAT
- Page 1 SealerSales W-300DAT 12" Table-Top Direct Heat Sealer w/ PTFE Coated Meshed Seal Instruction Manual...
- Page 2 Table-Top Direct Heat Sealers Models: W-300DAT, W-300DATS Distributed By: Version 1.0_2014...
-
Page 3: General Information
General Information Thank you for purchasing our W-Series Direct Heat Sealers. This owner’s manual contains information relating to your sealer. The manual will provide you with basic information concerning both operation and maintenance of your new machine. Please read it carefully as failure to do so may result in bodily injury and/or damage to the equipment. Please fill in the information below. -
Page 4: Safety Instructions
W H D H W H D H I N S T R U C T I O N I N S T R U C T I O N M A N M A N U A L Safety Instructions Safety Instructions Below are general safety precautions and warnings that should be Below are general safety precautions and warnings that should be... - Page 5 W H D H I N S T R U C T I O N M A N U A L Never touch the sealing bars with your bare hands while the sealer is plugged into a power source, in operation or just finished operation. Touching heated areas may cause fire and/or severe burns. While machine is in operation, do not place fingers, tools, or other foreign objects on or into the machine.
- Page 6 Introduction W-Series Direct Heat Sealers are designed for sealing many different types of thermoplastic materials including: coated aluminum foil, Kraft paper, cellophane, polypropylene, poly-nylon, and other thicker materials up to 20mil in total thickness. Please note that our direct heat sealers would not be appropriate for sealing polyethylene and/or polyvinyl chloride.
-
Page 7: Specifications
How Do W-Series Direct Heat Work? Basic Our W-Series direct heat sealers maintain constant heat in both sealing jaws. Principles Direct heat sealers consume power as long as the sealers remain on thus providing Place material on lower better heat penetration than impulse sealers. The temperature and length of the sealing bar. - Page 8 Getting to Know your Direct Heat Sealer Temperature Controller Protector Bars Adjust temperature Bars protect operator Power Switch depending on material from the sealing bars Turn on when you are ready to use your sealer Sealing Timer Adjust sealing time based on material to be sealed (0-6 secs) Lower Sealing Bar...
-
Page 9: Electrical Circuit Diagram
Electrical Circuit Diagram Figure 4. Electrical Circuit Diagram for W-Series Direct Heat Sealers... -
Page 10: Operation
Operating your Operating your Sealer Assembly Instructions Assembly Instructions 1. Connect the footswitch to the sealer unit. Connect the footswitch to the sealer unit. 2. To install the optional working plate and table optional working plate and table, remove screws located at the front of the unit and at the front of the unit and install the working plate. - Page 11 7. When sealer is not in use, turn off the power switch When sealer is not in use, turn off the power switch. Please note: Sealing bars will be extremely hot. Do not touch the Please note: Sealing bars will be extremely hot. Do not touch the sealing bars as this could cause severe burns.
-
Page 12: Maintenance
Maintenance The following maintenance procedures should be followed to ensure the longevity of your The following maintenance procedures should be followed to ensure the longevity of your The following maintenance procedures should be followed to ensure the longevity of your W-Series Direct Heat Sealer. - Page 13 Replacing Heater (s) Our W-Series Direct Heat Sealers will require new heaters from time to time. There are two heaters found on the unit, one in the upper sealing jaw and one in the lower sealing jaw. Remove the old heater on either the top and/or bottom sealing jaw. Unscrew the heater loose from the sealing jaw and base of sealer.
- Page 14 3. Unscrew the heaters from the bottom sealing jaw in order to remove the thermostat sensor from the sealing jaw. Note: In order to fully remove and install the thermostat, one may also need to separate the head of the sealer from the base. Figure 11.
-
Page 15: Parts Diagram
Parts Diagram Figure 14. Spare Parts Diagram Overview... - Page 16 Item Part # Description Comments WHDH-1 Control Set Bracket WHDH-1a Bolt/Washer to attach control unit to body M6x25 WHDH-2 Upper Bracket/Jaw (same as W-300T, but with holes) WHDH-2a Bolt and Washer for attaching the Upper Jaw/ Lower Jaw to the Seal Bar M6 x 30 WHDH-2b Bolts (Washer and Nuts) to attach Upper Jaw to Control Unit WHDH-1/2...
-
Page 17: Troubleshooting
Troubleshooting Problem Possible Causes Solution Upper and/or lower sealing bars 1. Heater(s) are worn out. 1. Replace heaters(s) on the unit. not heating Unit does not heat up (both jaws are 1. Heater(s) are worn out. 1. Replace heaters(s) on the unit. not heating up) 2.
Need help?
Do you have a question about the SealerSales W-300DAT and is the answer not in the manual?
Questions and answers