Related Manuals for Siemens SIDS-T40026-00-4AUS
Summary of Contents for Siemens SIDS-T40026-00-4AUS
- Page 1 SIDS-T40026-00-4AUS SIERS Siemens integrated electrical racking system instruction manual for SIMOVAC non-arc- resistant and SIMOVAC-AR arc-resistant medium-voltage motor controllers usa.siemens.com/simovac...
- Page 2 SIERS Siemens Integrated Electrical Racking System | Instruction manual Hazardous voltages and high-speed moving parts. Will cause death, serious injury, or property damage. Always de-energize and ground the equipment before maintenance. Read and understand this instruction manual before using equipment.
-
Page 3: Table Of Contents
The contents of this instruction manual shall not become part of or modify any prior or existing agreement, commitment or relationship. The sales contract contains the entire obligation of Siemens Industry, Inc. The warranty contained in the contract between the parties is the sole warranty of Siemens Industry, Inc. -
Page 4: Introduction
Refer to the instruction manual IC1000- and open/disconnect the isolating switch for F320-A105-XX-4A00 for the specific the SIMOVAC and SIMOVAC-AR medium- controller. voltage controllers while standing at a location remote from the controller compartment. Figure 1: SIERS Siemens integrated electrical racking system mechanism... -
Page 5: Receiving And Inspection
Instruction manual | SIERS Siemens Integrated Electrical Racking System The normal method of operation employs a Field service operation and hand-held control pendant on a 30 ft warranty issues (9.1 m) cord for remote control. Optionally, Siemens can provide competent, well-... -
Page 6: Description And Control
SIERS Siemens Integrated Electrical Racking System | Instruction manual Description and control Description and control The SIERS electrical racking system circuit includes miniature circuit breaker protection The SIERS electrical racking system is for both the 125 Vdc and 120 Vac supplies (if powered by 125 Vdc or (optionally) by 120 Vac power from the controller. -
Page 7: Hand-Held Remote Control (Control Pendant)
Instruction manual | SIERS Siemens Integrated Electrical Racking System Figure 3: SIERS control circuit Hand-held remote control (control pendant) Hand-held remote control Note: The TEST pushbutton and LED are (control pendant) disabled when the pendant is used with The hand-held control pendant includes SIERS in SIMOVAC or SIMOVAC-AR. -
Page 8: Interlocks And Operation Control
SIERS Siemens Integrated Electrical Racking System | Instruction manual Interlocks and operation control Interlocks and operation control 2. Normally open contact to sense door Item Description There are three interlock permissive circuits position. Power supply 125 wired for every controller cell that is... -
Page 9: Control Using Hand-Held Control Pendant
Instruction manual | SIERS Siemens Integrated Electrical Racking System Control using hand-held control pendant Control using hand-held control pendant Figure 5: Hand-held control pendant The hand-held control pendant can be used to operate the SIERS racking system from a distance of up to 30 ft (9.1 m) from the... - Page 10 SIERS Siemens Integrated Electrical Racking System | Instruction manual Item Description Pin used for moving the slider up and provides access to the lever Lever access Figure 7: Mechanical and electrical interlock for manual operation...
-
Page 11: Operation Sequence
Instruction manual | SIERS Siemens Integrated Electrical Racking System Operation sequence Operation sequence Press the pushbutton for the OPEN/ The operation sequence that follows DISCONNECT position. Please note it is describes the control using the hand-held not necessary to hold the button control pendant. -
Page 12: Alarms And Troubleshooting
SIERS Siemens Integrated Electrical Racking System | Instruction manual Alarms and troubleshooting Alarms and troubleshooting • Motor time out Note: If none of these The SIERS electrical racking system includes If the racking process takes more time troubleshooting actions resolves the issue, contact... -
Page 13: Manual Racking
Instruction manual | SIERS Siemens Integrated Electrical Racking System Manual racking Manual racking When the manual racking process is necessary follow these steps: Open the MCB to disconnect control power from the SIERS racking system. Follow the normal procedures contained in the applicable SIMOVAC... - Page 14 SIERS Siemens Integrated Electrical Racking System | Instruction manual...
- Page 15 Instruction manual | SIERS Siemens Integrated Electrical Racking System...
- Page 16 Published by Siemens Industry, Inc. 2020. Siemens Industry, Inc. 7000 Siemens Road Wendell, NC 27591 For more information, including service or parts, please contact our 24/7 Customer Support Center: Phone: +1 (800) 333-7421 To request a service or parts quote online, visit: www.usa.siemens.com/techsupport or e-mail...
Need help?
Do you have a question about the SIDS-T40026-00-4AUS and is the answer not in the manual?
Questions and answers