Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Wickes PBS900G.1
Summary of Contents for Wickes PBS900G.1
- Page 1 BELT SANDER 920W 76x533MM PBS900G.1 223740...
-
Page 2: Table Of Contents
CONTENTS GENERAL POWER TOOL SAFETY WARNINGS SAFETY WARNINGS FOR SANDER COMPONENT LIST ACCESSORIES TECHNICAL DATA SYMBOLS NOISE INFORMATION OPERATING INSTRUCTIONS WORKING HINTS MAINTENANCE ENVIRONMENTAL PROTECTION PLUG REPLACEMENT (ONLY FOR REWIRABLE PLUG OF UK & IRELAND) DECLARATION OF CONFORMITY... -
Page 3: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings, 3. PERSONAL SAFETY instructions, illustrations and specifications a) Stay alert, watch what you are doing and use provided with this power tool. Failure to follow all common sense when operating a power tool. Do instructions listed below may result in electric shock, fire and/ not use a power tool while you are tired or under the influence of drugs, alcohol or medication. -
Page 4: Safety Warnings For Sander
likely to bind and are easier to control. the power tool before making any adjustments, changing accessories, or storing power tools. Such g) Use the power tool, accessories and tool bits etc. preventive safety measures reduce the risk of starting the in accordance with these instructions, taking into power tool accidentally. -
Page 5: Component List
COMPONENT LIST Dust bag Front handle Belt tracking adjustment knob Dust exhaust outlet Variable speed control Lock on button Belt tension release lever On/Off switch Rear handle... -
Page 6: Accessories
ACCESSORIES Dust extraction adapter Dust bag 80 Grit sanding belt We recommend that you purchase your accessories from the same store that sold you the tool. Use good quality accessories marked with a well-known brand name. Choose the type according to the work you intend to undertake. Refer to the accessory packaging for further details. -
Page 7: Noise Information
NOISE INFORMATION A weighted sound pressure : 82dB(A) A weighted sound power : 93dB(A) & K 3.0dB(A) Wear ear protection when sound pressure is over: 80dB(A) VIBRATION INFORMATION Vibration total values (triax vector sum) determined according to EN60745: Vibration value emissioa Vibration emission value a = 5.08m/s Uncertainty K=1.5m/s... -
Page 8: Operating Instructions
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. 1. INSTALLING THE SANDING BELT (See Fig A1, A2) WARNING! Remove the mains plug from the socket before changing sanding belt. Pull the lever (9) to release the belt tension. Remove and fit a new belt over both rollers. - Page 9 3. DUST BAG(See Fig. C1, C2) You must use the dust bag provided to collect the dust produced during sanding. To attach, insert the dust bag (6) into the dust extraction outlet (2). Make sure the dots of the outlet are locked in the slot of the dust bag. When the dust bag is full, remove and empty by opening the zip on the dust bag (5).
- Page 10 5. VARIABLE SPEED CONTROL(See Fig. E) Adjust the variable speed control dial (8) to increase or decrease the speed according to the material and sanding belt specification to be used (also possible during no load operation). See the table below for general guidance on speed selection.
- Page 11 8. DRIVE BELT REPLACEMENT (See Fig G1, G2) Remove screws WARNING! Remove the mains plug from the socket before carrying out a drive belt replacement. Do not attempt to remove the drive belt until the belt wheel has cooled down. Remove the screws and the belt cover as shown.
-
Page 12: Working Hints
WORKING HINTS FOR YOUR BELT SANDER If your power tool becomes too hot, especially when used at low speed, set the speed to maximum and run with no load for 2-3 minutes to cool the motor. Avoid prolonged usage at very low speed. Always use a sanding belt suited to the material you wish to sand. -
Page 13: Plug Replacement (Only For Rewirable Plug Of Uk & Ireland)
PLUG REPLACEMENT (ONLY FOR REWIRABLE PLUG OF UK & IRELAND) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: Blue = Neutral Brown = Live As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. -
Page 14: Declaration Of Conformity
DECLARATION OF CONFORMITY Wickes Building Supplies Limited Declare that this product: BELT SANDER Description and SKU code: 223740 Complies with the following Directives and Regulations: 2006/42/EC, Machinery Directive 2014/30/EU, Electromagnetic Compatibility Directive 2011/65/EU & (EU)2015/863 (RoHS),Restriction of Hazardous Substances Directive... - Page 16 Customer Helpline 0345 2005409...