Related Manuals for GSI Group PNEG-1614
Summary of Contents for GSI Group PNEG-1614
- Page 1 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin Installation Manual PNEG-1614 Date: 07-30-09 PNEG-1614...
- Page 2 PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
-
Page 3: Table Of Contents
Assembling the Platform ........................9 Assembling the Stairs ........................11 Adding the Handrails ........................17 Assembling Intermediate Platform (Optional Package #STR1143) ..........20 Chapter 3 Warranty ............................23 PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... -
Page 4: Chapter 1 Safety
CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. NOTE indicates information about the equipment that you should pay special attention. PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... -
Page 5: Safety Instructions
Keep all parts in good condition and properly installed. Fix damage immediately. Replace worn or broken parts. Remove any Maintain Equipment built up grease oil and debris. and Work Area PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... - Page 6 Hard Hat Wear hard hat to help protect your head. Wear appropriate fall protection equipment when working at elevations greater than six feet (6'). Fall Protection PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
-
Page 7: Chapter 2 Installation
Bolt Spaces around Bin with 2.66" Corrugation Rings Bolt Spaces Inches 131-1/4 168-3/4 206-1/4 243-3/4 281-1/4 318-3/4 356-1/4 393-3/4 431-1/4 468-3/4 506-1/4 543-3/4 Figure 2B PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... - Page 8 6. Each additional stair wall bracket (LDR-4082) will be placed 32" below the previous and four (4) standard bolt spaces or 37-1/2" from the previous. There will be a total of four (4) steps for each additional ring. PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
-
Page 9: Assembling The Platform
This must all be assembled at the same time using 5/16" hardware. Note the color codes, placement, and orientation of the platform vertical angles. Figure 2E PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... - Page 10 2. Installation Figure 2F shows the assembly of the platform handrails. These must also be attached using 5/16" hardware. Figure 2F PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
-
Page 11: Assembling The Stairs
5/16" hardware. Bolt heads should be installed on the front side of the steps. Step components for standard STR1071 package Figure 2G Step components for special top STR1073 package. All components color coded Red. Figure 2H PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... - Page 12 Figure Figure 2I Stair Bracing Inside View Figure 2J Stair Bracing Outside View PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
- Page 13 Attach the tie straps on the inside and outside of the steps as shown. Use special two (2) steps from STR1073 package (color code: Red) (See Figure 2H on Page 11.) Figure 2K Bin diameters up to 60' Figure 2L PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
- Page 14 2. Installation Bin diameters 60' to 72' Figure 2M Bin diameters 75' to 78' Figure 2N Bin diameters 90' to 105' Figure 2O PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
- Page 15 13-14. Continue attaching tie straps on the inside and outside of the steps. Continue with standard four (4) step packages (refer to Figure 2G on Page 11.) Figure 2P PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
- Page 16 The bottom section’s upper handrail will also have to be field fit with an extra drilled hole for attachment to the bottom handrail post. PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
-
Page 17: Adding The Handrails
Use two (2) 3/8" x 1" flange bolts and nuts to attach the handrail post to the horizontal wall bracket. (See Figure 2T on Page 18.) Make sure the post is plumb before tightening the bolts. Figure 2S PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... - Page 18 5/16" x 1-1/4" Bolt and nut Four (4) step handrail (STR1077) 5/16" x 1-1/4" Bolt and nut Figure 2U Upper Handrail Connection Figure 2V Upper Handrail Connection PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
- Page 19 Equal amounts should be cut from both of the handrails. Large intermediate handrail (LDR-4087) 5/16" x 1-1/4" Bin bolt and nut Small intermediate handrail (LDR-4088) Figure 2W Intermediate Handrail PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
-
Page 20: Assembling Intermediate Platform (Optional Package #Str1143)
Use 5/16" hardware at all the connection points. Note the center floor brace (LS-6701) is offset from the center of the platform. (The bin wall is hidden for clarity.) Figure 2Y PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin... - Page 21 5/16" hardware. Note the orientation of the vertical angles. Figure 2Z Figure 2AA shows the assembly of the platform handrails. These must also be attached using 5/16" hardware. Figure 2AA PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
- Page 22 A hole will have to be drilled in the handrail to attach to the handrail post. It can be attached in the same way as previous discussed in the manual. PNEG-1614 Heavy Duty Bin Stairs and Platform Assembly for 2.66" Corrugated Bin...
-
Page 23: Chapter 3 Warranty
GSI Group, LLC Limited Warranty The GSI Group, LLC (“GSI”) warrants products which it manufactures to be free of defects in materials and workmanship under normal usage and conditions for a period of 12 months after sale to the original end-user or if a foreign sale, 14 months from arrival at port of discharge, whichever is earlier. - Page 24 Authorities having jurisdiction should be consulted before installations are made. GSI Group 1004 E. Illinois St. Assumption, IL 62510-0020 Phone: 1-217-226-4421 Fax: 1-217-226-4420 www.gsiag.com Copyright © 2009 by GSI Group Printed in the USA...
Need help?
Do you have a question about the PNEG-1614 and is the answer not in the manual?
Questions and answers