Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Seville Classics airLIFT OFF65944B/48B
Summary of Contents for Seville Classics airLIFT OFF65944B/48B
- Page 1 ® airLIFT 2-Button Electric Height Adjustable Standing Desk Model #: OFF65944B/48B Please contact Seville Classics for help with assembly and to report any damaged or missing components. Phone: 1 (800) 323-5565 Email: Support@SevilleClassics.com Homepage: www.SevilleClassics.com 013021...
-
Page 2: Safety Instructions
Safety Instructions FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATING INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY Read and understand this manual before attempting to install or Assure that everyone who uses this product is informed of the contents of this manual. -
Page 3: Quick Setup
Quick Setup! Only takes 15 minutes to complete. Phillips screwdriver required. Keep the top in the box during assembly to protect it from scratches. Controller Box Legs Motor Feet... -
Page 4: Parts List
Parts List A. Top (1) B. Legs (1) C. Feet (2) D. Controller (1) Tools & Hardware List E. M6x12 Screw (4) F. ST 4.8x13 Screw (4) G. M8x30 Screw (8) H. 4 mm Hex Key (1) I. 5 mm Hex Key (1) J. - Page 5 STEP 1. Lower LEGS (B) onto the back of the TOP (A). Make sure the motor is on the same side as the control box. Motor Control Box STEP 2. Align the holes on the legs with the brackets and attach with M6x12 SCREWS (E) using 4 mm HEX KEY (H).
- Page 6 STEP 3. Align holes on crossbar with holes on back of TOP (A). Attach with two ST4.8x13 SCREWS (F) using Phillips screwdriver. STEP 4. Align holes on CONTROLLER (D) with holes on edge of TOP (A). Attach with two ST4.8x13 SCREWS (F) using Phillips screwdriver. Organize cables with ZIP-TIE (J) and FASTENERS (K).
- Page 7 STEP 5. Connect cables from the motor to the CONTROLLER (D). Connect cables from motor to control box. STEP 6. Attach FEET (C) to the bottom of table legs with four M8x30 BOLTS (F) using 5 mm HEX KEY (I).
- Page 8 STEP 7. Plug the power cable into the control box. Make sure the cables from the controller to the motor to the control box are securely attached. Power cable Take this time to make sure all screws, bolts, and cables have been secured tightly.
- Page 9 WARNING: TWO PEOPLE ARE NECESSARY TO TURN TABLE. DESK IS HEAVY. LIFT WITH EXTREME CAUTION. STEP 8. Turn the desk onto its feet. Lift with 2 people TIP: Screw the leveling feet in and out as necessary to ensure the desk stands level. DO NOT put weight on desk yet.
-
Page 10: Use Instructions
Use Instructions DESK MUST BE INITIALIZED BEFORE FIRST USE Up Arrow Down Arrow Initialize & Reset Press and hold the Down Arrow until the desk reaches its lowest point. Initialization is complete when the desk emits a chime sound and rebounds. When RST appears on the display, follow the above instructions to reset. - Page 11 Troubleshooting Problem Action Desk does not go up or down and the controller Check all connections. Make sure power cord is plugged into the control box does not illuminate when any button is and a power outlet. Press any button on the controller and make sure it illumi- pressed.
-
Page 12: Warranty Information
The liability of Seville Classics under the warranty shall be limited to the amount paid by the customer for the product. Seville Classics shall not be liable for any loss of use of the product, or other incidental or consequential costs, expenses or damages incurred by the customer or other user. - Page 13 • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced Radio/TV technician for help MADE IN CHINA Seville Classics, Inc. / 19401 Harborgate Way Torrance, CA 90501 / USA...