Advertisement
Quick Links
Advertisement
Related Manuals for Malouf POWER-FLEX 2
Summary of Contents for Malouf POWER-FLEX 2
- Page 1 POWER-FLEX POWER-FLEX OWNER’S MANUAL...
- Page 2 • Power-Flex 2 • Only connect this product to a properly grounded • Always unplug this bed from the electrical outlet before cleaning or •...
- Page 3 (2) this device must accept any interference received, including interference that may cause undesired operation. • Power-Flex 2 • To comply with the FCC RF exposure requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirement and void user’s right...
- Page 4 POWER-FLEX OWNER’S MANUAL CONTENTS Overview Assembly Remote Control Electrical Components and Backup Battery Synchronizing Two Bases Test All Functions / Additional Help Warranty Information...
- Page 5 Head Motor Foot Motor OWNER’S MANUAL Control Box OVERVIEW USB Ports Retainer Bar Power Supply Box Power-Flex 2 ( ) -Inch Legs Power Cord ( ) -Inch Legs (6) End Caps Wireless Remote Control ( ) Leg Sets Included Sync Cable...
- Page 6 POWER-FLEX OWNER’S MANUAL ASSEMBLY A minimum of two people are required to assemble this adjustable Open box on the floor in the flat bottom facing to avoid Place the box in the room the bed will be used with the bottom of the box facing Carefully remove packaging taking care not to puncture the box with any sharp...
- Page 7 POWER-FLEX OWNER’S MANUAL Middle Leg on King Size Only Head ASSEMBLY Hand tighten all six legs for King into the bed frame until Note that there are two location options for each an outside placement or an inside Tighten the legs in the location of your maintaining a consistent inside or outside location Take care not to over tighten...
- Page 8 POWER-FLEX OWNER’S MANUAL ASSEMBLY With two to four the bed by the metal frame and turn it over so the mattress side is facing up Take caution not to the bed with the or to use the legs as pivot points causing angled pressure as this may cause Move the bed to the desired...
- Page 9 POWER-FLEX OWNER’S MANUAL ASSEMBLY To install the mattress retainer insert one end of the retainer bar in its respective slot until it slides fully into place Flex retainer bar to insert the other end on the other Plug the power cord into the wall outlet and run the test on pages of this You may want to familiarize yourself with the remote control functions prior to running the...
- Page 10 POWER-FLEX OWNER’S MANUAL REMOTE Head Up Foot Up CONTROL Overview All of the functions of the bed can be operated with the remote The remote Head Down Foot Down control comes with buttons that will automatically adjust when or you can manually control adjustments using the arrow buttons on the remote See the diagram to the right for a complete list of remote control Flat...
- Page 11 POWER-FLEX OWNER’S MANUAL REMOTE Overview CONTROL The original remote that comes in the box is already paired to the No further PAIRING action is In the event that the remote is not paired with the begin by checking the Ensure the remote batteries are Replace if Ensure the power cord is plugged into a powered The blue pairing button can also be...
- Page 12 POWER-FLEX OWNER’S MANUAL ELECTRICAL COMPONENT SETUP Overview Sync Cable Input The electronic components are and no assembly is some input locations are important for proper setup and Head Motor Input USB Input functionality Foot Motor Input USB Input...
- Page 13 POWER-FLEX OWNER’S MANUAL ELECTRICAL COMPONENT SETUP USB ports are located under the head portion of the bed base at two locations To access the USB press the Head Up button to raise the bed and reveal the USB Once your device is plugged into the USB you may lower or adjust the bed to your...
- Page 14 POWER-FLEX OWNER’S MANUAL BACKUP Overview BATTERY Use two batteries only If a power outage install the batteries into the power supply to allow temporary power to the base Unplug the power cord from the outlet and remove the cover from the compartment on the underside of the power supply Place two batteries...
- Page 15 POWER-FLEX OWNER’S MANUAL SYNCHRONIZING (for Twin XL and split sizes only) Ensure both bases plugged into a power Make sure Remote A was already paired to Base A and Remote B was paired to Base pair them by following the instructions found on pages remotes are paired to their respective...
- Page 16 POWER-FLEX OWNER’S MANUAL SYNCHRONIZING (for Twin XL and split sizes only) Place two Twin XL or split size adjustable bases next to each other in desired Plug in Sync Cable to the control box of each base into the “Program” input on the control box With the connecting cable use remote and test all functions of the bed...
- Page 17 POWER-FLEX OWNER’S MANUAL TEST ALL FUNCTIONS Head Up Head Down Foot Up Foot Down Flat Overview Zero Gravity To ensure proper use remote and test all functions for Anti Snore...
- Page 18 POWER-FLEX OWNER’S MANUAL NOTES: ADDITIONAL HELP Check under the bed base to verify the wired connections are secure and there are no cords or bedding obstructing the movement of the Make sure the batteries are installed correctly or install two new AAA batteries into the remote Ensure the remote control is synced with the control box on the Check to ensure the power cord is properly...
- Page 19 fitness for a particular purpose and all other warranties otherwise arising by operation of law, course of dealing, custom, trade, or otherwise. Malouf® shall not be liable for any consequential damages or losses arising from the purchase, installation and/or use of this product.