Alcatel-Lucent Enterprise OmniAccess Stellar AP1301 Series Installation Manual page 2

Table 2
Ethernet Port Pinout
Signal
Connector Pin
Name
1 RJ45_DA+
2 RJ45_DA–
1
3 RJ45_DB+
2
3 4 RJ45_DC+
4
5 RJ45_DC–
5
6 RJ45_DB–
6
7
7 RJ45_DD+
8
8 RJ45_DD–
Table 3
Console Port Pinout
Connector Pin Signal Name
3 TXD
1
2
4 GND
3
4
5 GND
5
6 RXD
6
7
Pins not listed are not connected.
8
Table 4
RS-485 Port Pinout
Connector Pin Signal Name
1 RS485_B
1
2
2 RS485_A
3
4
4 GND
5
5 GND
6
7
Pins not listed are not connected.
8
Note: The serial console port allows you to connect the AP to a

serial terminal or a laptop for direct local management. This port
is an RJ-45 female connector with the pinouts described in Table 3.
Currently for use by Service & Support only.
Note: The RS-485 port allows you to connect the AP to a RS-485
terminal. The maximum allowable current of PSE 12V power output
is 300mA. In addition, PSE 12V power output can be turned on and
off by software. This port is an RJ-45 female connector with the
pinouts described in Table 4.
Power
The OAW-AP1301 series access point supports direct DC power adapter
(48V DC nominal, sold separately) and Power over Ethernet (PoE).
The DC power connector port is located on the back of the device, as
shown in Figure 3.
The PoE allows the Ethernet port to draw power from an IEEE
802.3at compliant source.
OmniAccess Stella AP supports the power adapter provided by ALE
ONLY.
PoE
Before You Begin
PoE-
Refer to the sections below before beginning the installation process.
PoE-
Pre-installation Checklist
PoE+
Before installing your OAW-AP1301 Stellar access point, be sure that
PoE+ you have the following items:
•
8-conductor, CAT5 or better UTP cable of required length.
PoE+
• One of the following power sources:
IEEE 802.3at compliant Power over Ethernet (PoE) source
◼
PoE+
(PoE switch or PoE injector).
AC-DC adapter (sold separately)，output voltage DC 48V,
PoE- ◼
output current
PoE- • A terminal or a notebook
Identifying Specific Installation Locations
You can mount the OmniAccess Stellar AP on a ceiling rail or on a
wall. You should first determine the location of the installation. The
installation position is located at the center of the required
Function
coverage area and should be free from obstructions or obvious
sources of interference.
Transmit
•
Minimize the number of obstructions (such as walls) between the
Ground
AP and user terminals.
•
Electronic equipment or devices (such as microwave ovens) which
Ground may produce radio frequency noise should be away from the
installation position of the AP .
Receive
It is strictly prohibited to install around stagnant water, water seepage,
leakage or condensation. Avoid cable condensation or water seepage
along the cables connecting to the AP.
AP Installation
Refer to mounting kits installation Guide.
Verifying Post-Installation Connectivity
Function
The LED on the AP can be used to verify that the AP is receiving power
and initializing successfully.
Data-
Product Specifications
Data+
OAW-AP1301 series Dimensions/Weight
Ground Unboxed OAW-AP1301:
•
Net Weight: 1.64lbs / 0.74kg
Ground • Dimensions (HxWxD): 7.1 inches x 7.1 inches x 1.42 inches
(18 cm x 18cm x 3.6cm)
Environmental
• Operating :
▪ Temperature: 0°C to +50°C (+32°F to +122°F)
Humidity: 10% to 90% non-condensing
▪
• Storage and transportation :
▪ Temperature: -40°C to +70°C(-40°F to +158°F)
For additional specifications on this product, please refer to the
Datasheet.
Contacting Alcatel-Lucent Enterprise
0.6A
≥
Website Support
Main Site https://www.al-enterprise.com/
Support Site https:// businessportal2.alcatel-lucent.com
Support Email ebg_global_supportcenter@al-enterprise.com
Telephone Support
North America 1-800-995-2696
Latin America 1-877-919-9526
Europe +800 00200100 (Toll Free) or +1(650)385-2193
Asia Pacific +65 6240 8484
Other Region 1-818-878-4507