SET Lynx-CustomFit LYNX2-MPO Installation Manual

ETK1123235A
For your safety operation
The Lynx-CustomFit® Splice-On Connector is designed and
manufactured to assure personal safety. Improper operation
can result in bodily injury and serious damage to this product.
Please read and observe all warnings instructions given in this
operation manual.
Wear safety glasses
!
handling optical fiber.
Never look into the end of a microscope or optical
!
cable connected to an optical output device that is
operating. Laser radiation is invisible, and direct
exposure can severely injure the human eye.
Alcohol is flammable, causes irritation and is harmful
!
if swallowed or inhaled. Keep alcohol away from
heat, sparks, skin, and avoid contact with eyes.
In the case of the work at the high place, please be
!
careful not to drop an assembling tool.
Composition
Disposable
Holder (*1)
Front
Housing
Dust Cap
Polish Surface and Housing Color
SM Low Loss SM Std. Loss MM62.5 OM1 MM50 OM2
8 degree Polish
Yellow Green
North Carolina (USA)
Sumitomo Electric Light wave Corp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL +1-919-541-8100
http://www.sumitomoelectric.com/
Copyright © 2011 Sumitomo Electric Industries, LTD.
Lynx - CustomFit
Lynx - CustomFit
- LYNX2
- LYNX2
to protect your eyes when
Rear Parts
Rear
Boot
Stopper
Protection
Sleeve
MT STUB
Dummy Cap
w/ Tether
(*1) 1 pc / 100 connectors
Flat Polish
Beige Black
London (UK)
Sumitomo Electric Europe Ltd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL +44 (0)20-8953-8118
http://www.sumielectric.com/
® Splice - On Connector
® Splice - On Connector
- MPO for Ribbon
- MPO for Ribbon
Installation Manual
Installation Manual
1. Improper assembly will result in a loss of performance.
Please read instructions
and the operation manual of the fusion splicer.
2. Never touch the fiber of the
in the factory.
3. The product is sensitive to dirt or dust. Do not take out
any parts from the package
4. The characteristic will be influenced by the fiber
cleaved surface condition. Please use a cleaver which
has a good cleaving characteristic.
5. Do not remove the dust cap
been completely assembled
high insertion loss due to them.
Below equipments and tools are required.
Fusion Splicer
T-66M12-MPO
Furcation
Tube
Cord Tool
LYNX2-CORDTOOL-2&3
Splicer
T-66M12-
MPO
MM50 10G
SMF : G.652, G.657
OM3
MMF : MM50(OM2), MM50(OM3), MM50(OM4), MM62.5(OM1)
Please perform Arc test prior to the splicing operation.
Aqua
(See the operation manual of the splicer.)
*Ribbon fiber for testing is included in the connector kit.
Please check fiber type inside the field fiber.
Ver. 2
Ver. 2
Cord -
Cord -
Precautions
given in this operation manual
stub. It has been inspected
until it is to be
until the connector has
in order not to cause an
Assembling Tools
Fiber Cleaver Jacket Remover
FC-6M JR-6
Kevlar Cutter
Recommended Program
Fiber Splicing Program
SMF SM12c: Lynx MPO SM
MMF MM12c: Lynx MPO MM
Yokohama (Japan)
Sumitomo Electric Industries, Ltd.
(Lightwave Network Products Division)
1, Taya-cho, Sakae-ku, Yokohama 244-8588, Japan
TEL +81-45- 853-7223, http://global-sei.com/fttx/
used.
Fiber Holder
FHM-12
Heater Program
Lynx MPO