Advertisement
6.
SA12/S - AIR HAMMER
The air hammer is designed primarily for use on vehicle bodywork. We do not recommend any other use.
WARNING! Ensure that you read, understand and apply the safety instructions in Section 1 before use. Additionally the following
safety instructions are specific to this tool.
Ensure chisels are correctly rated for the job. DO NOT use damaged or suspect chisels.
DO NOT switch the hammer on whilst the chisel is in contact with the workpiece.
DO NOT use hammer where there is flammable liquid, solids or gas such as paint solvent, including waste wiping or cleaning rags etc.
WARNING! DO NOT chisel any materials containing asbestos.
Operation
6.1. Insert the chisel shank into the gun cylinder (fig.3).
6.2. Place the retainer ring over the chisel (fig.3) and lower onto the hammer's cylinder thread. Screw the retainer spring on to the cylinder using
a clockwise motion and using pressure on tag B until the spring is fully located (fig.4) and the chisel is retained by the spring's retaining tag (B).
6.3. Connect the hammer to the air supply as in Section 4.
6.4. To operate the hammer, squeeze the trigger, taking care that the chisel end is not in contact with the work-piece. The air regulator can be
adjusted by means of the knob at the base of the handle, use this as a means of throttle control.
6.5. To remove attachment, reverse procedures 6.1. and 6.2. using pressure on tag A.
fig.3
The SA12/S.V2 Medium Stroke Air Hammer, when operated in accordance with these instructions and tested in accordance with EN 28662-1:
1993 results in the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . 25.3m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 10 minutes in any 8 hour period.
This duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
7.
SA21/S - AIR RATCHET WRENCH
The air ratchet wrench has a hardened steel anvil with trigger operated power control, it is suitable for use in the engine bay where there is limited
space for hand operated ratchets.
WARNING! Ensure that you read, understand and apply the safety instructions in Section 1 before use. Additionally the following
safety instructions are specific to this tool.
DO NOT use any additional force upon the wrench in order to remove or tighten a nut.
Only use sockets specifically designed for use with a ratchet wrench.
Operation
7.1. Connect the wrench to the air supply as in Section 4.
7.2. Place the socket over the subject nut and depress the trigger to operate the wrench.
7.3. To change ratchet direction turn the switch on the tool head. F = Forward R = Reverse.
7.4. The flow of air (torque) may be regulated by turning the screw above the trigger.
The SA20/S Air Ratchet Wrench, when operated in accordance with these instructions and tested in accordance with EN 28662-1: 1993 results
in the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . . 7.0m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 125 minutes in any 8 hour period.
This duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
Risk of Hand Arm Vibration Injury.
Uncertainty: . . . . . . . . . . . . . . . . . 10.1m/s²
Risk of Hand Arm Vibration Injury.
Uncertainty: . . . . . . . . . . . . . . . . . . 2.8m/s²
Original Language Version
fig.4
SA2004KIT Issue: 2 - 05/11/09
Advertisement
