Nero 8101-5 Quick Manual

1. Purpose
Remote Control is designed to control remotely the executive devices
of the Radio series, as well as executive devices of the Nero series
(only with static code) using transcoder Nero 8361 UPM.
2. Specifications
Operating frequency range, MHz........................................................................................433,05–434,79
Maximum power of emitted signal, not more than, MW...........................................................................10
Number of control channels..........................................................................................................................5
Number of devices for feedback mode (one per channel)...........................................................................5
Battery type (number of pieces) ................................................................................................CR2032 (2)
Battery voltage, V...........................................................................................................................................3
Overall dimensions, mm...............................................................................................................129×40×15
Operation temperature range, °С.............................................................................................from 0 to +40
Degree of frame protection.....................................................................................................................IP40
3. Peculiarities
- transmission of control commands with static or dynamic code. Factory setting – dynamic code.;
- 5 control channels plus 1 shared channel. The shared channel is not available for programming, it only
manages devices;
- operation mode* with improved dynamic code and feedback support.
This mode is necessary for visual confirmation of remote control commands. If the device does not
respond to the command, the remote control reports an error with three beeps and three flashes of the
corresponding channel indicator. If the command is executed successfully, there are no instructions.
*Remote control operation modes:
1 - static;
2 - dynamic;
3 - improved dynamic (default settings);
4 - improved dynamic with feedback.
4. Programming
Recording the remote control channel into the memory of the executive device
1. Input the executive device in the programming mode (see manual for the corresponding device).
2. Select a recorded channel.
3. Record a channel:
a) in dynamic mode: press the «STOP» button and, without releasing it, briefly press the «UP »
button, then release both.
b) in static mode: briefly press the «STOP» button.
c) in dynamic mode with feedback:
- press the «STOP» and «UP» buttons simultaneously;
- release the «UP » button without releasing the «STOP» button- get a signal from the remote
about successful recording to the device.
Changing the remote control code: selection of dynamic or static code
1. Enter the «remote control mode Selection» menu: press and hold the «STOP» button for more
than 4 seconds.
2. Select the desired mode by short pressing the «UP» or down buttons.
3. Exit the menu: press and hold the «STOP» button for more than 1 second. The remote control will
also automatically exit the menu after 8 seconds.
Delete the remote control channel from the memory of the executive device
1. Input the executive device in the programming mode (see manual for the corresponding device).
2. Select a deleted channel.
3. Delete a channel:
a) in dynamic mode: press the «STOP» button and without releasing it, briefly press the
«DOWN» button, release both.
b) in static mode: press and hold the «STOP» button for more than 1 second, then release;
c) in dynamic mode with feedback:
-press simultaneously button «STOP» and «DOWN» button;
-release the «DOWN» button while holding down the «STOP» button.
Сalibration (removing devices that did not respond to the remote control in feedback mode)
When you calibrate the remote control, all channels are cleared of devices that did not respond to
the remote request.
Calibrate the remote control: press the «DOWN» and «UP» buttons simultaneously, release any of
them after the first beep, and press it again. Hold the buttons until you get a response from the
remote control (but no more than 8 seconds).
Opening / closing control channels
1. Enter the menu for closing / opening channels: press and hold the channel selection button for
more than 4 seconds.
2. Select the desired channel by short pressing the channel selection button.
3.
a) Close the channel: press the «DOWN» button.
b) Open a channel: press the «UP» button.
4. Exit the channel opening/closing menu — automatically after 5 seconds.
Five-channel Remote Control 8101-5
Action
Passport
Channel indicator
Сhannel selection
UP/TURN ON
STOP/TURN OFF
DOWN/OFF
Confirmation of record on the executive device depends on the programming type and mode: short-long-
short green flash on the indicator or long-term movement «DOWN», short-term «UP-DOWN» movement
and long-term «UP» movement of the roller shutter.
Remote display in dynamic mode with feedback:
- channel recorded: 1 beep and 1 flashing diode of the recorded channel;
- channel not recorded: 3 beeps and 3 flashing diodes of the recorded channel.
1. All channel indicators start blinking.
2. Number of flashes of the remote control indicator:
1 flash — static mode;
2 flashes — dynamic operation mode;
3 flashes — improved dynamic mode;
4 flashes — improved dynamic mode of operation with feedback.
Confirmation of deletion on the executive device depends on the programming type and mode: one long-
term red flash or long-term «DOWN-UP» movement of the roller shutter.
Remote display in dynamic mode with feedback:
- channel deleted: 2 beeps and 2 flashing diodes of the channel being deleted;
- channel not deleted: 3 beeps and 3 flashing diodes of the deleted channel(see the instructions on the
remote control) in red.
Information from the remote control:
3 beeps and 3 flashes of all indicators.
1. 4 remote control channel indicators are lit (all except the first one).
2. The indicator for the selected channel is not lit.
3. Indication:
a) channel closed: 3 short flashes;
b) channel open: 1 long flash.
Fig. 1 — Assignment of remote control buttons
Indication
1