Related Manuals for RHINO Solar Pro
Summary of Contents for RHINO Solar Pro
- Page 1 Rhino Solar Pro - Omni Adjustable Skidsteer Mounted Pile Driver Operation And Parts Manual...
-
Page 2: Table Of Contents
6.2.1 Drive Post .......................16 6.2.2 Pull Post ......................18 7. Maintenance ..................21 7.1 Hammer Lubrication ..................21 7.2 Grease Fittings .....................21 7.3 Lubricate Mast Chain ..................22 7.4 Telescoping Tubes ..................22 7.5 Adjust Hammer Down Pressure ..............23 Rhino Solar Pro Adjustable Pile Driver... - Page 3 Table Of Contents 8. Troubleshooting ................24 9. Warranty ..................... 25 10. Parts....................26 10.1 Mast ......................26 10.2 Center Section ...................30 10.3 Lower Frame ....................34 10.4 Hydraulic Hoses And Fittings ..............36 Rhino Solar Pro Adjustable Pile Driver...
-
Page 4: Introduction
Information provided in this manual was current as the pile driver. of the issue date. Rhino Tool Company reserves the right to make design changes without further notice or liability. This manual explains the operation and routine maintenance of the Rhino Solar Pro Pile Driver. -
Page 5: Safety
Do not operate, work on or around pile driver Indicates a situation that could result in while fatigued, while under the influence of damage to the machine or other property. alcohol, prescription or nonprescription medication or if feeling ill. Rhino Solar Pro Adjustable Pile Driver... -
Page 6: Mount And Dismount Properly
Workers and bystanders must use ear protection Have underground utilities located before beginning while pile driver is in operation. work. In the US or Canada, call 811 (US) or 888- 258-0808 (US and Canada). Rhino Solar Pro Adjustable Pile Driver... -
Page 7: Pressurized Fluids
Wear personal protective equipment appropriate for riders on the pile driver. the job. Always use Rhino Tool Company replacement parts. Not using Rhino Tool parts may cause harm to personnel and may void the warranty. Rhino Solar Pro Adjustable Pile Driver... -
Page 8: Lockout/Tagout
Never use your hand to check for leaks; use a piece of wood or cardboard. If fluid of any kind is injected into the skin, seek immediate medical attention. ^ WARNING Cancer and reproductive harm. more information www. P65Warnings.ca.gov. Rhino Solar Pro Adjustable Pile Driver... -
Page 9: Safety Decals
If the safety decal is no longer legible, replace it with a new one. Contact your Rhino Tool dealer for new decals. The Decal A - 00601 part number of the decal is located on the decal and on the images of the safety decals that follow. - Page 10 Safety Decal C - 00602 Decal E - 00604 Decal F - 00605 Decal D - 00603 Decal G - 00606 Rhino Solar Pro Adjustable Pile Driver...
- Page 11 Safety Decal H - 00607 Decal J - 00609 Decal K - 00610 Decal I - 00608 Rhino Solar Pro Adjustable Pile Driver...
-
Page 12: Specifications
3,000 lbs (1,5360 kg) Hydraulic Requirements 2 Lines - Pressure And Tank Hydraulic Oil Flow Range 10.5 - 22.5 gpm (40 - 80 lpm) Hydraulic Oil Pressure Range 1740 - 2320 psi (2120 - 160 bar) Rhino Solar Pro Adjustable Pile Driver... -
Page 13: Components
Components 4. Components Hammer Mast Mast Tilt Up/Down Cylinder Control Panel Lower Frame Operators Manual Holder/Case Quick Attach Frame Mast Tilt Fore/Aft Cylinders Mast Position Fore/Aft Cylinder Mast Position Left/Right Cylinder Rhino Solar Pro Adjustable Pile Driver... -
Page 14: Transporting
Connect properly rated tie down devices to pile driver and to truck or trailer. Tighten tie down devices as instructed by the manufacturer to secure pile driver to truck or trailer. Rhino Solar Pro Adjustable Pile Driver... -
Page 15: Operation
Dry firing hammer without a post engaged Electrocution can occur without direct may damage hammer. contact. Maintain a 20 ft (6 m) clearance from any electrical line. Contacting a gas line can result in an explosion. Rhino Solar Pro Adjustable Pile Driver... -
Page 16: Drive Post
Release lever when mast is in a straight up (100 LPM) DOWN RIGHT position. RHINO TOOL WWW.RHINOTOOL.COM COMPANY LEFT DOWN MAX OIL SUPPLY HAMMER HAMMER MAST MAST MAST MAST 26 GPM TILT TILT (100 LPM) DOWN RIGHT RHINO TOOL WWW.RHINOTOOL.COM COMPANY Rhino Solar Pro Adjustable Pile Driver... - Page 17 Post must be inside of bracket on mast as shown. Maintenance Section. Adjust mast position if needed. LEFT DOWN MAX OIL SUPPLY MAST MAST MAST HAMMER HAMMER MAST 26 GPM TILT TILT (100 LPM) RIGHT DOWN RHINO TOOL WWW.RHINOTOOL.COM COMPANY Rhino Solar Pro Adjustable Pile Driver...
-
Page 18: Pull Post
HAMMER MAST MAST MAST MAST 26 GPM TILT TILT (100 LPM) DOWN RIGHT Tilt mast down to horizontal storage position using lever (A) before detaching from skid steer. RHINO TOOL WWW.RHINOTOOL.COM COMPANY Storage Position Rhino Solar Pro Adjustable Pile Driver... - Page 19 LEFT DOWN MAX OIL SUPPLY MAST HAMMER HAMMER MAST MAST MAST 26 GPM TILT TILT (100 LPM) RIGHT DOWN RHINO TOOL WWW.RHINOTOOL.COM COMPANY Rhino Solar Pro Adjustable Pile Driver...
- Page 20 (A) before traveling. Travel at a slow speed. Repeat steps 3-16 for each additional post. ^ WARNING Roll over hazard. Pile driver mast must be in the horizontal storage position before disconnecting from skid steer. Rhino Solar Pro Adjustable Pile Driver...
-
Page 21: Maintenance
Lower mast to horizontal position before checking for leaks. Never use your hand to check for leaks; use a piece of wood or cardboard. If fluid of any kind is injected into the skin, seek immediate medical attention. Rhino Solar Pro Adjustable Pile Driver... -
Page 22: Lubricate Mast Chain
Stored outside and heavy/daily use - Weekly. • Stored inside and heavy use - Every 2 weeks. • Stored inside and light use - Every 3-4 weeks. • Use a lithium spray grease suitable for chains. Rhino Solar Pro Adjustable Pile Driver... -
Page 23: Adjust Hammer Down Pressure
Turn screw (A) clockwise to increase down pressure, or counter clockwise to decrease down pressure. Turn screw (A) 1/2 turn increments. Hold screw (A) in position and tighten locknut (B). Test operation. Adjust as needed to get desired down pressure. Rhino Solar Pro Adjustable Pile Driver... -
Page 24: Troubleshooting
Lower frame lifting off ground Too much down pressure. Adjust down pressure in during operation. Maintenance Section. Hammer not staying in contact Not enough down pressure. Adjust down pressure in with post during operation. Maintenance Section. Rhino Solar Pro Adjustable Pile Driver... -
Page 25: Warranty
Rhino Tool Company warrants the original purchaser, purchasing the equipment in new condition, that the Rhino Skid Steer Attachment will be free from defects in workmanship and materials, for a period of one (1) year. This warranty is non-transferable, and does not include the Furukawa Hydraulic Hammer, which is backed by Furukawa’s Limited Warranty. -
Page 26: Parts
Parts 10. Parts 10.1 Mast Rhino Solar Pro Adjustable Pile Driver... - Page 27 Level Bubble 360237 Plug 360243 360252 Bracket 504003 Hex Bolt 500178 Hex Bolt 500180 Hex Bolt 551302 Spring Pin 995335 Steel Pin With Wire Lock 360244 500178 Hex Bolt 518806 Hex Nut 500010 Hex Bolt Rhino Solar Pro Adjustable Pile Driver...
- Page 28 Parts Mast, Continued Rhino Solar Pro Adjustable Pile Driver...
- Page 29 Wear Slide - Notched 360114 Wear Slide - Chamfered 360115 Plate 360116 Wear Slide - Notched 360117 Wear Slide - Chamfered 360161 Weldment - Tensioner 360157 Weldment - Tensioner 504021 Hex Bolt 504025 Screw Rhino Solar Pro Adjustable Pile Driver...
-
Page 30: Center Section
Parts 10.2 Center Section Rhino Solar Pro Adjustable Pile Driver... - Page 31 500029 Hex Bolt 360242 360254 Spanner Wrench 360255 Spanner Wrench 360257 Manual Storage Case 504004 Hex Bolt 504006 Screw 504017 Hex Bolt 504018 Flat Washer 504020 Hex Bolt 518801 Lock Nut 518802 Lock Nut Rhino Solar Pro Adjustable Pile Driver...
- Page 32 Parts Center Section, Continued Rhino Solar Pro Adjustable Pile Driver...
- Page 33 360192 Cylinder 360193 Cylinder 360206 Control Valve 504022 Flat Washer 504005 Flat Washer 504000 Flat Washer 504005 Flat Washer 500001 Hex Bolt 360051 Wear Slide 306232 Elbow Fitting 306230 Hydraulic Fitting 360231 Hydraulic Fitting Rhino Solar Pro Adjustable Pile Driver...
-
Page 34: Lower Frame
Parts 10.3 Lower Frame Rhino Solar Pro Adjustable Pile Driver... - Page 35 Parts Item Part Number Description 360011 Frame Weldment 360025 Frame Weldment 360030 Plate 504002 Hex Bolt 518806 Hex Nut 504000 Flat Washer 500029 Hex Bolt Rhino Solar Pro Adjustable Pile Driver...
-
Page 36: Hydraulic Hoses And Fittings
10.4 Hydraulic Hoses And Fittings Note: Item numbers are referring to hose assembly to and from connecting points. Rhino Solar Pro Adjustable Pile Driver... - Page 37 Hydraulic Male Quick Disconnect Coupling (SAE), Qty 1 801194 Hydraulic Female Quick Disconnect Coupling (SAE), Qty 1 360155 10-12 Hydraulic Connector, Between 360208 And 801195, Qty 1 360246 Check Valve, Between 801194 And 360209, Qty 1 Rhino Solar Pro Adjustable Pile Driver...
- Page 38 Hydraulic Hoses And Fittings, Continued 13 14 Note: Item numbers are referring to hose assembly to and from connecting points. Rhino Solar Pro Adjustable Pile Driver...
- Page 39 Mast Tilt Left/Right 360224 Hose, Control Valve Port 13 To Mast Tilt In/Out Load Hold Valve Mast Tilt Up/Down 360223 Hose, Control Valve Port 14 To Mast Tilt In/Out Load Hold Valve Mast Tilt Up/Down Rhino Solar Pro Adjustable Pile Driver...
- Page 40 Hydraulic Hoses And Fittings, Continued P Port 15/34 T Port 17 18 15/34 Port A Port B Note: Item numbers are referring to hose assembly to and from connecting points. Rhino Solar Pro Adjustable Pile Driver...
- Page 41 Hose, Relief Valve Port B to Mast Extend Cylinder Base End 360222 Hose, Mast Tilt In/Out Load Hold Valve To Tilt Cylinder Base End 360240 Hose, Mast Tilt In/Out Load Hold Valve To Tilt Cylinder Base End 360236 12 x 8 Fitting, Reducer Rhino Solar Pro Adjustable Pile Driver...
- Page 42 Hydraulic Hoses And Fittings, Continued Side View Note: Item numbers are referring to hose assembly to and from connecting points. Top View Rhino Solar Pro Adjustable Pile Driver...
- Page 43 Hose, Mast Tilt L/R Load Hold Valve To Right Cylinder Rod End 360227 Hose, Right Tilt Cylinder Rod End To Left Tilt Cylinder Base End 360227 Hose, Front Tilt Cylinder Base End To Rear Tilt Cylinder Rod End 360248 0.35 x 17 Inch Nylon Strap Rhino Solar Pro Adjustable Pile Driver...
- Page 44 Rhino Tool Company 1134 West South Street PO Box 111 Kewanee, IL 61443 309-853-5555 www.rhinotool.com Revision: February 2021...