Advertisement
Quick Links
8 Thank you for purchasing the AHUJA
Please read this manual thoroughly before making connections and turning on the
8
power. Following the instructions in this manual will enable you to obtain optimum
performance from your new AHUJA
Please retain this manual for future reference.
8
®
Feedback Terminator
AFT-24F2M
Automatic Feedback Terminator
Automatic Feedback Terminator
Automatic
AF T-24F2 M
.
.
Advertisement
Summary of Contents for Ahuja AFT-24F2M
- Page 1 Feedback Terminator AFT-24F2M AF T-24F2 M 8 Thank you for purchasing the AHUJA Automatic Feedback Terminator Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum...
- Page 2 Cleaning: Disconnect this equipment from the AC mains and external battery before cleaning. Clean with a damp cloth, but do not allow any lequid to enter the set. Do not clean with liquids or aerosols. AFT-24F2M...
-
Page 3: Table Of Contents
Connector Wiring ........10 Specifications ........11 AFT-24F2M... -
Page 4: General Description Of Product
• General Description of Product AFT-24F2M is a Dual Channel Digital Signal Processor. It is designed to provide state of the art feedback suppression and controlled processing, for fixed installations and live events, through simple and intuitive switch interface. AFT-24F2M provides up to 24 notch filters for each channel CH1 &... -
Page 5: Front Panel Controls & Features
LED. Press & release this the processor ON. Push the bottom switch to BYPASS the processor part of the knob to switch the settings, which is indicated by processor OFF. continuous glow of bypass switch knob LED. AFT-24F2M... -
Page 6: Rear Panel Controls & Features
2. socket can be used for connecting 13. Input Connectors for Channel 2 balanced/unbalanced input signal to Either female XLR or stereo jack channel 1. socket can be used for connecting 11. LOCK Switch balanced/unbalanced input signal to AFT-24F2M... -
Page 7: Setup And Live Modes Of Operation
LEDs will be ON. may be set in low Q mode ie.1/5th 7. Now keep the lock switch in ON octave . position so that the terminator settings Notch Filter Q Diagram Music 1/80th Octave Speech 1/5th Octave 1.2k 820 850 AFT-24F2M... -
Page 8: Typical Applications - Live Programme
A F T- 2 4 F 2 M r e s p e c t i v e l y, input signals is enough so that through suitable connecting 0dB LED of AFT-24F2M lights cables. up continuously. AFT-24F2M... -
Page 9: Typical Applications - Conference System Setup
Ahuja Conference Systems CM-4000 and two numbers of 6.3mm and CM-5000. (1/4”) mono jack plug on the other end, should be made AFT-24F2M can be used to according to pin connections control the feedback problem detailed below. in any conference setup. This... -
Page 10: Connector Wiring
TIP: SIG Pin-2: +SIG Pin connections of a 6.3mm (1/4") Pin-3: -SIG Pin-1: GND Mono Phone Plug for connecting unbalanced signal in Input & Output. b) Output (Unbalanced) SLEEVE: GND Pin-2: SIG Pin-3: GND Pin-1: GND SLEEVE TIP: SIG AFT-24F2M... -
Page 11: Specifications
2× Male XLR and 2×6.3mm (1/4”) stereo jack socket SIGNAL TO NOISE RATIO 106dB FREQUENCY RESPONSE 20-20,000Hz (-1dB) DISTORTION 0.01% CROSSTALK 100dB A/D & D/A CONVERSION 24 bit SAMPLING RATE 48kHz POWER REQUIREMENT 220-240V AC 50/60Hz DIMENSION W483 × H45 × D200 mm WEIGHT 2.40kg AFT-24F2M... - Page 12 ® l We cannot be held responsible for printing errors, should they occur. is a registered trademark of Ahuja Radios in India and other countries. l © Copyright Ahuja Radios, 2018. All rights reserved. Any unauthorized reproduction or use of logos, images or design elements is strictly prohibited by law.