ION Operator's Manual page 9

NO. PROBLEM
11 Battery charger indicates that the charging battery is "too cold"
(solid red LED) when the battery is at room temperature.
12 Drilling lights come on, powerhead will not turn, all (3) battery
LEDs indicate a full charge. Unit WILL run with a different battery.
13 Drilling lights come on, powerhead runs smoothly with no load
on it, and turns normally with full power until it stops cutting
ice. Hole count is significantly reduced from normal operation.
(Battery indicates (2) or (3) LEDs)
14 Drilling lights come on, powerhead will not turn, all (3) battery
LEDs indicate a full charge.
15 Drilling lights do not come on, but powerhead functions normally. LED system has failed or Controller is
16 Drilling lights stay ON all of the time; must remove battery to turn
them off.
17 Drilling lights come on, powerhead makes a "clicking noise" from
the top of the motor cover, and will not turn. Battery LEDs indicate
a full charge. ("ON" switch has been held down for more than 5
seconds, battery core temperature is not frozen). WITH BATTERY
DISCONNECTED, transmission CAN be turned over by hand, in
either direction without stopping.
18 Drilling lights come on, powerhead makes a "clicking noise" from
the top of the motor cover, and will not turn. Battery LEDs indicate
a full charge. ("ON" switch has been held down for more than 5
seconds, battery core temperature is not frozen). WITH BATTERY
DISCONNECTED, transmission CANNOT be turned over by hand in
either direction without stopping.
19 Hole count has drastically and quickly reduced. Hole count cannot
be increased by switching batteries or even powerheads. (The
blades are new)
20 Auger jumps on the ice and will not cut.
21 Auger spins at normal speed, but cuts slowly through the ice.
22 Powerhead functions normally, but hole count is drastically
reduced. Battery indicates a full charge. Drilling suddenly requires
downward force to be applied to the handlebars in order to cut
the ice.
23 Powerhead with Reverse, only runs in forward.
24 Powerhead with Reverse, only runs in reverse.
If above remedies fail, contact ION Customer Service at 800-345-6007 or info@ioniceaugers.com
Check for parts online at www.ioniceaugers.com or call 800-345-6007 M-F 8-5 CT
POSSIBLE CAUSE
Battery temperature sensor
malfunction.
Battery temperature sensor
malfunction.
Battery will charge normally, and
measures for good voltage, but has
no capacity.
Power switch is not depressed
completely.
not sending power to the LED system.
LED board has failed.
ION Motor is trying to turn, but
cannot due to low or incomplete
voltage to the motor.
ION Motor is trying to turn, but
cannot due to transmission problems.
Auger bit is damaged or bent.
Blades are dull or damaged or re-
sharpened incorrectly.
Blades are dull or damaged or re-
sharpened incorrectly.
Blades are dull or damaged or re-
sharpened incorrectly.
Reverse switch is faulty (open circuit)
or has become unplugged inside the
handlebar control, or Controller is
faulty.
Reverse switch is faulty (closed
circuit) or wiring has become loose
on switch and is touching each other,
or Controller is faulty.
to locate an authorized Service Center near you.
Operator's Manual
ION® Electric Ice Augers
REMEDY/ACTION
Replace battery.
Replace battery.
Replace battery.
Hold the switch for five seconds.
Install LED Light Kit or replace Controller.
Install LED Light Kit or replace Controller.
Remove access panel and Controller.
Check connection between the
Controller and the Motor connector. If
all connections are good, replace the
Controller.
Replace Motor/Transmission assembly.
Replace ice auger bit.
Replace with new blades.
Replace with new blades.
Replace with new blades.
Remove handlebar control, replace
Reverse switch or re-connect wiring.
(If switch and wiring is correct, replace
Controller).
Remove handlebar control, replace
Reverse switch or re-connect wiring.
(If switch and wiring is correct, replace
Controller).
9